Mechanic AK-KING11 ESD Straight Tweezer Red
₨ 1
Mechanic AK-KING11 Straight Tweezer
The Mechanic AK-KING11 straight tweezer gives your repair bench a red-coated, stainless steel ESD tool for handling small components on phone boards. The straight tip grips ICs, jumper wire, shield pads and flex connectors without crowding neighbouring parts. The anti-static build keeps static risk low when you work on live-sensitive PCBs. Technicians in Pakistan use it daily for IC change karna jobs, jumper lagana, board cleaning and reballing prep. Order it from Mechanicpk with the rest of your hot air, soldering and microscope setup.
Out of stock
Mechanic AK-KING11 Straight Tweezer for Precision Board Work
The Mechanic AK-KING11 straight tweezer belongs in the drawer of every technician who works at component level. It is a red-coated stainless steel tweezer from the Mechanic AK King series, built as an ESD anti-static tool for electronics repair. You use it for the unglamorous but constant tasks on a dead phone board: lifting a shield, steadying a small IC, positioning a jumper wire or pulling a flex out of its socket. A good pair rarely gets attention, but a poor pair slips, scratches pads and costs you a board.
Where a Straight Tip Earns Its Place
Straight tweezers suit work where you approach the part from above and need a clean, symmetrical grip. On a populated PCB, that means picking up small ICs, passives and filters, holding a component in place while hot air flows, and guiding a replacement part onto its pads. The straight geometry keeps the closing force aligned with your wrist, so you feel when the tip meets the part. If you mostly work around tall shields or tight corners, pair this model with an angled tweezer from the same range. Keep the straight one for flat, open areas of the board.
ESD Anti-Static Construction and Stainless Steel Body
Static discharge damages modern phone ICs silently, and the fault often shows up later as a charging issue or a hardware fault that never reproduces on the bench. The AK-KING11 carries an ESD anti-static specification, so you handle CPU-adjacent parts, power ICs and memory with less risk than a bare uncoated steel tool. The stainless steel body resists the flux, rosin and board-cleaning liquids that every technician uses daily. Wipe it after a reballing session and it stays ready for the next job.
Fitting the Tweezer into Your Repair Workflow
Reach for this tool at several stages of a board repair. During diagnosis, you hold a jumper wire against a test point while you read values with your multimeter. During rework, you steady an IC under a hot air station and lift it the moment the solder flows. During reballing, you position the chip over a stencil and move it to the PCB holder without disturbing the balls. During ISP and eMMC jobs, you place fine wires onto pinout points beside your test box or programmer. In each stage, the tweezer saves time because you stop hunting for a better grip.
Why Technicians and Shop Owners Stock It
A repair shop in Saddar or Hafeez Centre burns through tweezers faster than most tools. Tips bend, coatings wear and borrowed pairs disappear. The Mechanic AK King range has a reputation among technicians for consistent tips that stay aligned after daily use, which makes it a sensible standard for a whole bench or a training lab. Buying a few spares at once keeps every technician working with the same grip and feel. Combine it with a microscope for micro-soldering, a soldering station for pad repair and a reballing kit for BGA work, and you cover the core of a professional mobile repair setup.
Choosing Between Tweezer Types
Straight tweezers handle general component placement. Curved or angled versions reach under shields and into side-mounted connectors. Flat-tip versions lift flex cables and thin films. Most busy benches keep two or three types within reach. Start with the AK-KING11 if you want one dependable all-round straight tweezer, then add specialist shapes as your repair mix grows into camera modules, display flex and battery connector work.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Red-coated body for quick identification on a busy bench
- ✓Stainless steel construction
- ✓ESD anti-static design
- ✓Straight tip for top-down component grip
- ✓Mechanic AK King series build
- ✓Suits ICs, passives, wires and flex connectors
- ✓Works alongside hot air stations, soldering stations and microscopes
- ✓Universal use across phone brands and chipset families
Specifications
| Brand | Mechanic |
|---|---|
| Model | AK-KING11 (AK-11 King) |
| Category | Precision Tweezers |
| Technology | ESD anti-static |
| Material | Stainless steel |
| Tip Type | Straight |
| Color | Red |
Common Repair Uses
- ✓Component handling and fine placement on phone and electronics PCBs.
- ✓IC change karna: holding and lifting ICs during hot air rework
- ✓Jumper lagana: placing jumper wire on broken tracks and pads
- ✓Reballing prep: positioning chips over stencils
- ✓ISP and eMMC work: placing fine wires on pinout points
- ✓Charging issue repair: handling small charging-section components
- ✓Shield removal and refit
- ✓Flex connector handling during display problem repair
- ✓Board cleaning and inspection under a microscope
Compatible Devices
- ✓Universal repair tool, not device-specific. It works on the logic boards of any phone brand or chipset family.
- ✓Samsung Galaxy series boards
- ✓Oppo and Realme boards
- ✓Vivo boards
- ✓Infinix and Tecno boards
- ✓Xiaomi and Redmi boards
- ✓iPhone logic boards
- ✓Qualcomm and MediaTek based boards
- ✓Tablet and small-electronics PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the Mechanic AK-KING11 ESD safe for handling ICs?
Is the AK-KING11 a straight or angled tweezer, and what is it best for?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



