SUNSHINE P-3005DA DC Power Supply Adjustable 30V 5A
₨ 18,500
SUNSHINE P-3005DA 30V 5A Bench Supply
The SUNSHINE P-3005DA DC Power Supply Adjustable 30V 5A gives your repair bench a transformer-based linear source with 0–30V output, 0–5A current and a 150W rating. A 4-digit display shows voltage and current, with 1mV and 1mA resolution, so you read exactly what a dead phone draws the moment it powers up. Circuit, overload and over-temperature protection cover your boards during short-circuit hunting and boot loop diagnosis. A built-in 110V/220V selector lets you run it on local mains. Technicians use it on phone motherboards, tablet boards and general electronics benches across Pakistan.
In stock
SUNSHINE P-3005DA Linear Bench Supply for Board-Level Phone Repair
The SUNSHINE P-3005DA DC Power Supply Adjustable 30V 5A gives your bench a stable, measurable power source for diagnosing a dead phone before you reach for the hot air station. If you need a 30V 5A DC power supply for mobile repair, this unit covers the range most board-level jobs demand: 0–30V output, 0–5A current and a 150W rating from a transformer-based linear design. You read voltage and current on a 4-digit display, so you see what the board draws the second it powers up.
Why a 30V 5A DC Power Supply for Mobile Repair Starts Every Diagnosis
Every board-level repair begins with one question: what does the board draw when you feed it power? A battery cannot answer that. A bench supply can. You connect the P-3005DA to the battery terminals or the main power rail, set your voltage, and the current readout tells you whether the board is dead, shorted or partly alive.
A phone that shows no current draw points you toward a broken power path, a failed PMIC or an open connector. A phone that pulls high current the moment you power it points you toward a shorted capacitor or a damaged IC on the main rail. This single reading saves you from guessing, and it protects you from pulling the wrong IC. For a charging issue, a boot loop issue or a hang on logo case, the draw pattern during startup separates software faults from hardware faults before you open a flashing box.
Output Precision and Protection You Can Verify
The P-3005DA outputs 0–30V and 0–5A in a single channel, with 1mV voltage resolution and 1mA current resolution. That resolution matters when you chase small leakage currents on a standby rail or compare a suspect board against a known good one. The linear transformer design delivers a clean output, which gives you readings you can trust on sensitive phone logic boards.
Circuit protection, overload protection and over-temperature protection guard the supply and your repair target during long diagnosis sessions. Heavy copper-core output terminals give you a solid connection for the test cord that ships with the unit. If your bench runs several hours a day, those protection layers keep the supply working through short-circuit hunts and repeated power cycling.
Where the P-3005DA Fits in the Repair Workflow
Place this supply at the front of your workflow, before you reach for heavier equipment. Start with the power-on current check, then move to short isolation, component swaps and final verification. After you replace a PMIC or charging IC with a Hot Air Station and reflow it with your Soldering Station, the P-3005DA confirms the repair: you power the board and watch the current settle to a normal idle value.
The same supply supports flashing and programming work. When a phone goes dead after flash, a stable external power source lets you check whether the board still draws current before you reconnect eMMC Programmers, ISP Pinout Tools, UFS Adapters or Test Boxes. For FRP lock and pattern unlock jobs that need a powered board on the bench, the P-3005DA keeps the supply constant. You also pair it with Multimeters for rail measurements, Microscopes for visual inspection, PCB Holders for steady boards and Reballing Kits for BGA work.
Setup, Mains Selection and Bench Practicality
Set the rear selector to 110V or 220V before you plug in; the unit accepts AC110V/220V ±10% at 50/60Hz, so you match it to the mains at your workshop in Pakistan. It operates in a -10°C to 40°C environment at up to 90% relative humidity, which suits a busy workshop or service center bench.
At roughly 4.5kg, the transformer-based unit sits firmly on your bench and stays put while you clip leads. You get one supply that handles everyday phone boards at low voltage and extends to higher-voltage electronics up to 30V and 5A. For repair shop owners building out a bench, it replaces guesswork with a number on a display. For technicians, it becomes the first instrument you touch on every dead phone.
| Weight | 3.0 kg |
|---|
Key Features
- ✓Adjustable 0–30V output and 0–5A current from a single channel
- ✓150W rated output from a transformer-based linear design
- ✓4-digit display for voltage and current readout
- ✓1mV voltage resolution and 1mA current resolution
- ✓Circuit, overload and over-temperature protection
- ✓Copper-core output terminals for a secure test lead connection
- ✓Switchable AC110V/220V input at 50/60Hz
- ✓Test cord included for immediate bench use
Specifications
| Brand Entity | SUNSHINE |
|---|---|
| Product Entity | SUNSHINE P-3005DA DC Power Supply Adjustable 30V 5A |
| Technology Entity | Transformer-based linear regulated DC power supply, 0–30V / 0–5A, 150W |
| Compatible Device Entities | Android smartphone motherboards, iPhone logic boards, tablet boards, general electronics boards |
| Repair Process Entity | Power-on current diagnosis, short-circuit isolation, PMIC and charging IC verification |
| Industry Entity | Mobile phone repair, GSM hardware repair, PCB repair |
Common Repair Uses
- ✓Power-on diagnosis and short-circuit hunting on phone and electronics boards
- ✓Checking current draw on a dead phone
- ✓Locating a shorted component on the main power rail
- ✓Verifying PMIC and charging IC replacement
- ✓Diagnosing charging issue and boot loop faults
- ✓Testing a board after dead-after-flash failures
- ✓Powering a board without battery during bench repair
- ✓Confirming idle current after hardware fault repair
- ✓Powering boards during eMMC and ISP work
Compatible Devices
- ✓Universal bench supply, not device-specific; it powers any board whose input falls within 0–30V and 5A
- ✓Android smartphone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno and others)
- ✓iPhone logic boards
- ✓Tablet motherboards
- ✓Smartwatch and wearable boards
- ✓Power bank and charging circuit boards
- ✓Small laptop and notebook boards within 30V / 5A
- ✓Router and modem boards
- ✓General electronics PCBs within 30V / 5A
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the SUNSHINE P-3005DA work on 220V mains in Pakistan?
What protection and output resolution does the P-3005DA offer?
Related products
Sunshine M1 Pro Intelligent Height Adjustable Repair Table (72cm to 117cm)
In stock
YCS R1 Pro 1000W Hot Air Rework Station with 4 Nozzles
In stock
YCS S1-160W Ultra Soldering Iron Station for Mobile Repair
In stock


