Relife RL-044 XM13 Stencil for Redmi 9 / Note 9 CPU
₨ 599
Redmi 9 / Note 9 CPU Reballing Stencil
The Relife RL-044 XM13 Stencil gives you a 0.12 mm steel BGA plate for reballing the CPU on Redmi 9, Redmi Note 9 4G and Redmi Note 9 Pro boards. The XM13 plate targets the MediaTek MT6769V, Qualcomm Snapdragon 662 SM6115 and Snapdragon 750G SM7225 footprints, so you reball with a plate that matches the chip instead of improvising with a generic mesh. Pair it with a hot air station, quality flux and a microscope for dead phone and boot loop jobs that trace back to damaged CPU solder joints. Mechanicpk supplies it to Pakistani repair shops and service centers that run Xiaomi board-level work.
In stock
Relife RL-044 XM13 Stencil for Redmi 9 and Note 9 CPU Reballing
The Relife RL-044 XM13 stencil is a 0.12 mm steel BGA reballing plate for the CPU footprints on Xiaomi Redmi 9, Redmi Note 9 4G and Redmi Note 9 Pro motherboards. XM13 sits inside Relife’s RL-044 Xiaomi range, where every numbered plate matches one processor package, so you choose the plate that fits the chip on your board. This one covers the MediaTek MT6769V, the Qualcomm Snapdragon 662 (SM6115) and the Snapdragon 750G (SM7225). When a Redmi arrives as a dead phone, loops on boot or hangs on logo after a drop, a cracked CPU solder joint is one hardware fault you have to rule out, and a matched stencil gives you a repeatable way to fix it.
Technical Highlights of the XM13 Plate
Relife cuts the RL-044 range from steel at 0.12 mm thickness. That thickness sets the height of every solder ball you form, so the balls land at a consistent size and the CPU seats flat when you place it back on the board. Steel keeps its shape under the heat of a hot air station or preheater, and Relife lists high temperature and wear resistance for the range, so the plate survives repeated reballing cycles on a busy bench. The apertures use a round, full design with a precision hole pitch, which keeps paste or balls on their own pads and cuts down bridging between neighbors. Because XM13 targets three named CPU packages, you do not measure pitch or guess a fit. You read the marking on the chip, confirm MT6769V, SM6115 or SM7225, and start the job. Each plate in the RL-044 Xiaomi range carries its own number, so you match the footprint you work on most and add plates as your Xiaomi workload grows. The plate also works as a tin planting template: the apertures guide each ball to its pad, which removes the hand-placed errors that cause cold joints and uneven chip height.
Reballing Workflow with the Relife RL-044 XM13 Stencil
Start by lifting the CPU with a hot air station at a controlled temperature, then clean the board pads and the chip with desoldering wick, flux and isopropyl alcohol. Clamp the board in a PCB holder and fix the chip in a reballing jig under a microscope. Lay the XM13 plate over the chip and align every aperture with its pad before you apply anything, because a shifted plate gives you shifted balls. Spread solder paste or drop balls through the apertures, heat the chip briefly until the balls form, and lift the stencil once everything cools. Inspect the result under the microscope for missing balls and bridges, place the CPU back on the board, and check current draw with a multimeter after reassembly. This sequence turns a hardware fault diagnosis into a controlled repair instead of a guess.
Where XM13 Fits in Your Repair Line-up
XM13 belongs in the reballing kits section of any bench that handles Xiaomi volume. Redmi 9 and Redmi Note 9 boards pass through Pakistani repair shops and service centers every week, and a dedicated plate for their CPUs saves you from improvising with a mismatched stencil. Stock it next to the other XM plates for different Redmi and Mi processors, and pair it with a soldering station, a hot air station, a microscope and a PCB holder so the whole workflow stays in one drawer. If your bench grows from occasional reballing to daily CPU work, the full RL-044 Xiaomi set gives you the upgrade path from single plates to complete coverage. Check the chip marking before you order, since Redmi Note 9 variants use different processors. Repair counters in Lahore, Karachi and Islamabad save time by keeping one plate per common CPU, so a customer’s Redmi does not wait on a courier.
| Weight | 0.1 kg |
|---|
Key Features
- ✓0.12 mm steel BGA reballing plate
- ✓Matched footprint for the MediaTek MT6769V CPU
- ✓Matched footprint for the Snapdragon 662 SM6115 CPU
- ✓Matched footprint for the Snapdragon 750G SM7225 CPU
- ✓Round, full apertures with precision hole pitch
- ✓High temperature and wear resistance for repeated reballing cycles
- ✓Works as a tin planting template for even ball height
- ✓Part of the numbered RL-044 Xiaomi (XM) stencil range
Specifications
| Brand | Relife |
|---|---|
| Model | RL-044 XM13 |
| Category | BGA Reballing Stencil |
| Compatibility | Redmi 9 / Redmi Note 9 4G / Redmi Note 9 Pro CPU footprints (MT6769V, Snapdragon 662 SM6115, Snapdragon 750G SM7225) |
| Supported Devices | Xiaomi Redmi 9, Redmi Note 9 4G, Redmi Note 9 Pro |
| Technology | 0.12 mm tin planting (BGA reballing) stencil |
| Material | Steel |
Common Repair Uses
- ✓CPU-level reballing on Xiaomi Redmi boards
- ✓Reballing the MT6769V CPU after removal
- ✓Reballing the Snapdragon 662 SM6115 CPU after removal
- ✓Reballing the Snapdragon 750G SM7225 CPU after removal
- ✓Restoring solder balls on a CPU lifted from a Redmi dead phone board
- ✓Repairing weak CPU solder joints after drop damage
- ✓Reballing the CPU on boot loop or hang-on-logo boards with a suspected hardware fault
- ✓Re-tinning a replacement CPU before placement
- ✓Reballing under a microscope with a hot air station in a workshop
Compatible Devices
- ✓Xiaomi Redmi CPU footprints listed for the XM13 plate
- ✓Xiaomi Redmi 9
- ✓Xiaomi Redmi Note 9 4G
- ✓Xiaomi Redmi Note 9 Pro
- ✓MediaTek MT6769V CPU
- ✓Qualcomm Snapdragon 662 (SM6115) CPU
- ✓Qualcomm Snapdragon 750G (SM7225) CPU
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which CPUs does the Relife RL-044 XM13 stencil support?
What thickness and material is the RL-044 XM13 stencil?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



