AMAOE SAM15 Stencil SAMSUNG – S21 SM8350 BGA Reballing
₨ 599
Samsung S21 SM8350 BGA Reballing Stencil
The AMAOE SAM15 Stencil SAMSUNG gives you a 0.12mm BGA153 reballing pattern for Galaxy S21 series boards. It matches the Qualcomm Snapdragon 888 SM8350 and Exynos 2100 CPU, and supplier listings also name the RAM and PM8350 power IC. Use it on S21, S21+, S21 Ultra, G998U, G996U, Z Flip3, Z Fold3 and W22 boards after you lift the chip with hot air. Each order includes one stencil. Repair shops across Pakistan pick the SAM15 when a dead phone, boot loop issue or hang on logo fault calls for a clean CPU reball.
In stock
Samsung S21 SM8350 BGA Reballing Stencil by AMAOE
The AMAOE SAM15 Stencil SAMSUNG is a 0.12mm Samsung S21 SM8350 BGA reballing stencil built for the Galaxy S21 family. It carries the BGA153 ball pattern that technicians use when they reball the Snapdragon 888 SM8350 or Exynos 2100 CPU after removing it from the board. Supplier listings also name the RAM and the PM8350 power IC among the chips this pattern serves. Mechanicpk supplies the SAM15 to Pakistani repair shops that handle flagship Samsung boards and need a pattern matched to the chip, not a loose universal fit.
Where the SAM15 Fits in a Galaxy S21 Board Repair
You reach for the SAM15 when a Galaxy S21, S21+ or S21 Ultra arrives as a dead phone, a boot loop issue or a hang on logo fault that points to the CPU solder joints. After you lift the chip with a hot air station, both the chip and the board carry leftover solder that you must clean off first. Flux, desoldering wick and a microscope get the pads flat and bright. Then you seat the stencil over the chip, align every aperture with its pad, press solder paste through the 0.12mm openings and reflow the balls with controlled hot air. The result is a fresh ball array that sits correctly when you place the chip back on the board.
The same workflow applies to the RAM and the PM8350 power IC when a hardware fault traces back to those packages. A steady PCB holder keeps the board still during alignment, and a multimeter check on the rails after the repair confirms the new joints before you close the phone. The SAM15 targets one pattern family, so you spend less time hunting for the right mesh and more time on the bench.
Specification Detail Technicians Should Check
The AMAOE SAM15 BGA stencil uses a 0.12mm steel mesh with the BGA153 pattern. Supplier listings name the Qualcomm Snapdragon 888 SM8350 and the Exynos 2100 as the CPU targets, along with the RAM and PM8350 devices. The device list covers Galaxy S21, S21+, S21 Ultra, G998U, G996U, Z Flip3, Z Fold3 and W22. The package contains one stencil.
The 0.12mm thickness sets how much solder each aperture holds, which keeps the finished balls even across the array. Before you commit to the pattern, compare the chip marking on your board with the SM8350 or Exynos 2100 label. Samsung builds S21 phones with different processors by region, so the marking tells you more than the model number alone.
Choosing the SAM15 Within the Samsung Stencil Range
AMAOE numbers its Samsung stencils by board generation. The SAM15 covers the S21 generation, while supplier listings place the SAM16 on the A53 family and the SAM17 on the S22 series. Matching the stencil number to the phone generation prevents a mismatched ball pattern and a wasted reflow. If your bench handles mixed Samsung work, build the range around the models that arrive most often, then complete the workflow with Reballing Kits, a Hot Air Station and a PCB Holder. Shops in Pakistan that handle S21 series boards on a regular basis get the most value from keeping this stencil on the shelf. Browse the Soldering Stations, Microscopes and Multimeters categories at Mechanicpk to match the rest of your setup.
| Weight | 0.1 kg |
|---|
Key Features
- ✓0.12mm steel mesh for even solder ball formation
- ✓BGA153 ball pattern for the S21 generation CPU
- ✓Covers Snapdragon 888 SM8350 and Exynos 2100 processors
- ✓Fits S21, S21+, S21 Ultra, Z Flip3, Z Fold3 and W22 boards
- ✓Supplier listings also name the RAM and PM8350 devices
- ✓Direct-heating stencil format for hot air reballing
- ✓Numbered SAM15 model that sits within the AMAOE Samsung series
- ✓Single-piece pack for one-pattern bench use
Specifications
| Brand | AMAOE |
|---|---|
| Model | SAM15 |
| Category | BGA Reballing Stencils - Samsung |
| Compatibility | Samsung Galaxy S21 series CPU boards |
| Supported Devices | Samsung S21 / S21+ / S21 Ultra / G998U / G996U / Z Flip3 / Z Fold3 / W22 |
| Technology | 0.12mm BGA153 reballing stencil (Snapdragon 888 SM8350 / Exynos 2100) |
Common Repair Uses
- ✓CPU and related BGA reballing on Galaxy S21 series boards
- ✓Reballing the SM8350 CPU after removal
- ✓Reballing the Exynos 2100 CPU after removal
- ✓Reballing the RAM IC on the same pattern family
- ✓Reballing the PM8350 power IC
- ✓Restoring ball arrays on a dead phone after a drop
- ✓Re-tinning chips for a boot loop issue traced to CPU joints
- ✓Repairing a hang on logo fault linked to weak CPU solder balls
- ✓Preparing a chip for reinstall after pad cleaning
Compatible Devices
- ✓Samsung Galaxy S21 series boards with the Snapdragon 888 SM8350 or Exynos 2100 CPU
- ✓Samsung Galaxy S21
- ✓Samsung Galaxy S21+
- ✓Samsung Galaxy S21 Ultra
- ✓Samsung G998U
- ✓Samsung G996U
- ✓Samsung Galaxy Z Flip3
- ✓Samsung Galaxy Z Fold3
- ✓Samsung W22
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which chips does the AMAOE SAM15 stencil support?
Can I use the SAM15 for Samsung S22 or A53 boards?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



