2UUL SC02 Pre-Cut Thermal Silicone Pads 12x12x1.5mm

₨ 999

2UUL SC02 Pre-Cut Thermal Silicone Pads for Motherboard IC Work

The 2UUL SC02 is a pre-cut thermal silicone pad sized at 12 x 12 x 1.5 mm, supplied in a box of 100 pieces. You get a ready-to-use heat interface for board-level work, so you skip cutting pads at the bench. Technicians use these pads to shield nearby components while working on CPU and IC areas of a motherboard. Keep a box beside your hot air station and reballing kit, and you can protect sensitive neighbouring parts during every rework job.

Out of stock

10 People watching this product now!
Description

2UUL SC02 Pre-Cut Thermal Silicone Pads for Board-Level Repair

Your hot air and rework jobs run more smoothly when heat stays where you aim it. The 2UUL SC02 thermal pads give your repair bench a consistent silicone barrier for motherboard IC and CPU work. Each pad arrives pre-cut to 12 x 12 x 1.5 mm, so you start the job without measuring or trimming. A box holds 100 pieces, which keeps your bench stocked across many repair cycles. Treat these pads as a consumable accessory that supports your main tools rather than a standalone fix.

Pre-Cut Size and Pack Format

The pad measures 12 x 12 x 1.5 mm, which suits the footprint of many small board-level chip areas. You place the square directly over or beside the component you want to protect, then work around it with your hot air nozzle. If a chip area is smaller than the pad, you can trim the edge with sharp scissors and keep the cut piece for a later job. The 100-piece box gives you enough stock to cover several weeks of steady IC work in a typical repair shop. Store the unused pads in their sealed box so dust and debris stay off the silicone surface. Clean pads sit flatter on the board and make better contact with the area you protect.

Where the Pad Fits in Your Repair Workflow

The pad belongs in the rework stage of your workflow, after you have diagnosed the fault and before you apply heat to the target chip. Hot air removal and reballing both produce heat that can spread into neighbouring components on the same board. Place the pad to block that spread, then complete the lifting or soldering step with your station set to the correct profile. Pair the pad with a reballing kit, a PCB holder that keeps the board steady, and a hot air station with stable temperature control. When your shop grows into full-board rework, a larger hot air station becomes the logical upgrade. The pad still earns its place on that bench because it protects the parts that the station cannot isolate on its own.

Handling and Placement at the Bench

Handle each pad with clean tweezers, because fingerprints and oil reduce how well the silicone settles on the board surface. Check that the board area is clean and flat before you place the pad, since debris under the pad can lift its edges during heating. Press the pad gently into position so it sits square over the protected zone without covering the chip you plan to lift. After the job, remove the pad carefully and inspect both the pad and the board for residue. Discard any pad that has torn, lost its shape, or picked up flux. A disciplined handling routine keeps your box consistent and your results repeatable across the whole batch.

Additional information
Weight0.8 kg
Q & A
Please login to post questions

Key Features

  • Pre-cut 12 x 12 x 1.5 mm size, ready to place without trimming
  • 100 pieces per box for steady bench supply
  • Thermal silicone construction
  • Suited to hot air and rework workflows
  • Protects neighbouring components during board-level jobs
  • Easy to trim for smaller chip areas
  • Stores cleanly in its sealed box
  • Fits alongside reballing kits and PCB holders

Specifications

Brand2UUL
ModelSC02
CategoryPre-Cut Thermal Silicone Pads
CompatibilityUniversal, not device-specific
MaterialThermal silicone
Dimensions12 x 12 x 1.5 mm

Common Repair Uses

  • Shielding nearby components during hot air IC removal
  • Protecting adjacent parts while reballing a chip
  • Limiting heat spread across a motherboard during rework
  • Providing a silicone interface over CPU areas during board cooling tests
  • Covering sensitive chip zones during soldering on a phone board
  • Insulating neighbouring parts during a chip replacement job
  • Supporting bench workflows that combine hot air and PCB holders
  • Keeping heat away from connectors during board-level repair

Compatible Devices

  • Universal scope, not device-specific. Verified use areas are board-level chip zones on compact motherboards.
  • Smartphone motherboard CPU and power IC areas
  • Phone main board chip zones during soldering work
  • Laptop motherboard CPU and chip areas
  • PC CPU and chipset areas on compact boards
  • Board-level IC zones on any compact PCB
  • Chip areas adjacent to heat-sensitive components
  • Motherboard areas requiring temporary heat shielding
  • Chip zones that need a silicone interface during rework

FAQ

What is the product name?
The product name is 2UUL SC02 Pre-Cut Thermal Silicone Pads 12x12x1.5mm.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is SC02.
What is this product used for?
This product is used to shield nearby components and manage heat around chip areas during board-level repair.
Which devices are compatible with this product?
This product is compatible with a universal scope of board-level chip areas, not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What size is the 2UUL SC02 thermal pad?
The 2UUL SC02 thermal pad measures 12 x 12 x 1.5 mm.
How many pads come in one 2UUL SC02 box?
One 2UUL SC02 box contains 100 pieces.