2UUL SC31 Soldering Wire 0.3mm 100m 183°C 50g
₨ 900
0.3mm Fine Soldering Wire for Mobile Boards
The 2UUL SC31 soldering wire delivers a 0.3mm rosin flux-core tin wire with a 183°C melting point, spooled as 100 metres on a 50g reel. The thin gauge gives you precise control on small pads, flex connector rows and jumper points, so you place only the solder the joint needs. The low melting point keeps heat input down on dense smartphone logic boards. Mechanicpk supplies this spool to technicians who handle charging issue repairs, IC change jobs and track repair every day, and to shops that want a dependable fine-gauge consumable on the bench.
Out of stock
2UUL SC31 Soldering Wire for Fine-Pitch Mobile Board Work
The 2UUL SC31 soldering wire gives your repair bench a 0.3mm rosin flux-core solder with a 183°C melting point, wound as 100 metres on a 50g spool. Mechanicpk stocks it for technicians who work on dense smartphone logic boards, where thick wire floods pads and bridges neighbouring joints. The thin gauge lets you feed a controlled amount of alloy onto a single pad, a connector row or a jumper point without cleanup afterwards. If you tin tips, touch up pads or run jumper wires on dead phone boards every day, this spool covers that consumable need.
Wire Diameter, Flux Core and Melting Point
A 0.3mm diameter suits small pads, fine connector rows and component legs on modern boards. Thicker wire forces you to cut or flatten the tip of the bead to avoid bridges, while 0.3mm lets you touch the pad and feed exactly what you need. At 183°C, the wire melts well below common lead-free alloys, which sit around 217°C and higher. Your iron or hot air station needs less heat at the joint, and less heat at the pad lowers the risk of lifting a track or stressing a neighbouring component. The rosin flux core runs inside the wire, so flux reaches the joint the moment the solder melts. You skip brushing flux onto every pad for quick touch-ups, although badly oxidised pads still respond better to a little extra flux paste.
Where It Fits in a Mobile Repair Workflow
Fine solder wire shows up at several points in a board-level job. During charging issue repairs, you tin the pads before you seat a replacement charging port or connector. During IC change karna jobs, you clean the pads and lay a thin film of solder before the new chip goes down under hot air. When a track breaks, you run a jumper wire (jumper lagana) and flow a small bead at each end. For display problem and network issue boards, you reflow connector pads and re-solder lifted joints. Pair this wire with a temperature-controlled soldering station, a hot air station, a microscope for pad inspection and a PCB holder, and you cover the routine work of most repair benches. After a failed repair, reballing kits and this wire rebuild damaged pads before the chip returns to the board.
Spool Capacity for Daily Workshop Use
Each joint at 0.3mm consumes only a few millimetres of wire, so 100 metres lasts through a long run of repairs. A shop that completes several boards a day gets extended service from one spool, which keeps your cost per joint low. Store the spool in a dry place, away from heat and moisture, so the flux core and wire surface stay clean. Pull only the length you need and wipe your tip on brass wool or a damp sponge between joints so solder transfers cleanly every time. For technicians who buy consumables in volume, the 50g spool format makes restocking simple and keeps spare reels ready at each bench.
| Weight | 0.3 kg |
|---|
Key Features
- ✓0.3mm wire diameter for small pads and fine connector rows
- ✓183°C melting point to keep heat input low
- ✓Rosin flux core inside the wire
- ✓100m wire length per spool
- ✓50g spool for easy bench stocking
- ✓Fine control over solder quantity per joint
- ✓Suits soldering iron and hot air station work
- ✓Practical consumable for daily phone repair routines
Specifications
| Brand | 2UUL |
|---|---|
| Model | SC31 |
| Category | Soldering Wire |
| Compatibility | Universal soldering consumable for soldering irons and hot air station rework |
| Technology | Rosin flux-core solder wire |
| Material | Tin solder wire with rosin flux core |
| Wire Diameter | 0.3mm |
| Length | 100m |
| Weight | 50g |
| Melting Point | 183°C |
Common Repair Uses
- ✓Fine-gauge soldering on mobile phone boards and small electronics
- ✓Charging issue repair (port and connector soldering)
- ✓IC change karna: pad tinning before chip placement
- ✓Jumper lagana on broken tracks
- ✓Display problem repair: connector pad reflow
- ✓Network issue board touch-up
- ✓Lifted pad and joint re-soldering
- ✓Pad rebuilding after reballing or chip removal
- ✓Soldering iron tip tinning
Compatible Devices
- ✓Universal consumable, not device-specific; suits any smartphone or small electronics board that needs fine soldering
- ✓Smartphone logic boards (motherboards)
- ✓Charging port and connector pads
- ✓Display and flex connector pads
- ✓Battery connector pads
- ✓SMD component pads and legs
- ✓Jumper wire points on broken tracks
- ✓Pads prepared for IC change work
- ✓Soldering iron tip tinning
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What melting point does the 2UUL SC31 soldering wire have?
Is 0.3mm solder wire suitable for fine pads and jumper wire work on mobile boards?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



