Gsm-Sources 861 Series 6mm Hot Air Nozzle
₨ 1,200
6mm Nozzle for 861 Series Stations
The Gsm-Sources 861 series hot air nozzle 6mm gives your rework station a focused outlet for small-package board repair. You press it onto the handle of a compatible 861 series hot air station and aim heat at one IC, connector, or shield can without exposing the parts around it. The 6mm opening sits between fine-detail nozzles and wide chip nozzles, so it covers the everyday jobs on a repair bench. Keep one next to your station for charging IC work, audio IC removal, and flex connector rework.
In stock
861 Series Hot Air Nozzle 6mm for Precise Board-Level Rework
The 861 series hot air nozzle 6mm from Gsm-Sources gives your rework station a mid-narrow outlet for board-level repair. You push it onto the handle of a compatible 861 series station and direct heat at one component instead of a whole section of the board. At 6mm, the outlet suits small ICs, connectors, and shield cans. A wider nozzle would heat neighbouring parts, and a pin-point nozzle would leave cold corners on the package.
Where the 6mm Outlet Fits Your Bench Workflow
Phone boards pack components tightly. A 6mm outlet sits between the thin nozzles for tiny passives and the 10mm to 12mm nozzles for larger chips. You reach for it on charging IC change karna jobs, power management IC lifts, audio ICs, flex connectors, and small shield cans. When a customer brings in a dead phone with a charging issue, you usually need to lift one small IC without disturbing the capacitors beside it. This outlet size keeps the airflow concentrated on that package. Apply flux, set a conservative airflow on your station, and the small parts around the IC stay in place.
Compatibility with 861 Series Hot Air Stations
Gsm-Sources designed this nozzle for the 861 series platform. Before you order, confirm that your handle takes 861 series slip-on nozzles. The nozzle is a replacement and extension part, so it does not come with a heater or controller. Your station sets the temperature and airflow, and the nozzle shapes and delivers that air to the work area. This keeps your spare-nozzle stock simple, because one handle can switch between outlet sizes during a single repair.
Technique for Cleaner Rework
Hot air work rewards a steady hand and patience. Preheat the board area first, then bring the nozzle in a few millimetres above the package and keep it moving in small circles. A fixed nozzle on one spot overheats the corners of the IC and lifts nearby pads. Lead-free solder needs a higher station setting than leaded solder, so adjust the temperature on the station and watch the solder joints. Hold the board in a PCB holder, work under a microscope, and check the repair with a multimeter after reflow. After removing the IC, clean the pads before you place the new part.
Why Technicians Keep a 6mm Nozzle in the Drawer
Most repair benches handle small-package jobs every day, and the 6mm outlet covers the middle of that range. It works as your default for hardware fault diagnosis on charging, audio, and connector sections. You can move up to a wider nozzle for larger chips and back down to a finer nozzle for tight spots. If you build out your hot air workflow, look at hot air stations, reballing kits, and PCB holders in the related Mechanicpk categories.
| Weight | 0.1 kg |
|---|
Key Features
- ✓6mm outlet for focused airflow
- ✓Made for 861 series hot air stations
- ✓Slip-on fit on the handle
- ✓Suits small ICs and connectors
- ✓Covers shield can and connector work
- ✓Fits between fine and wide nozzle sizes
- ✓Replacement nozzle for busy repair benches
- ✓Works with standard flux and reflow technique
Specifications
| Brand | Gsm-Sources |
|---|---|
| Model | Nozzle 861 Series 6mm |
| Category | Hot Air Gun Nozzles |
| Compatibility | 861 series hot air rework stations |
| Technology | Hot air rework |
| Nozzle Size | 6mm |
Common Repair Uses
- ✓Small-package rework on phone and device boards.
- ✓Charging IC change karna
- ✓Power IC removal and replacement
- ✓Audio IC rework
- ✓Flex connector removal
- ✓Shield can lifting
- ✓Board cleaning and reflow
- ✓Dead phone hardware fault diagnosis
- ✓Pad preparation before reballing
Compatible Devices
- ✓Universal board-level use. Not tied to specific phone models. Fits 861 series hot air stations and works on any phone board that needs focused heat at small-package components.
- ✓Android smartphone motherboards
- ✓iPhone logic boards
- ✓Small charging ICs
- ✓Power management ICs
- ✓Audio ICs
- ✓Flex and board-to-board connectors
- ✓Small shield cans
- ✓Tablet and feature phone boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this 6mm nozzle fit all hot air stations?
Which repair jobs suit a 6mm hot air nozzle?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



