2UUL ST83 Heat Resisting Silicone Pad 400x280mm Gray

₨ 1

2UUL ST83 Silicone Repair Mat

The 2UUL ST83 is a heat resistant silicone mat for mobile repair. It measures 400 x 280 mm and insulates heat up to 500°C. The anti-dust coating keeps the grey surface cleaner during board-level work, and the soft, absorbent top protects your bench and your soldering tip during hot air and iron sessions. Technicians in Pakistan use it under hot air stations, soldering stations and PCB holders for IC change karna, reballing and charging port jobs. The corrosion-resistant silicone wipes clean with banana oil or panel cleaner, so flux and residue come off between repairs.

Out of stock

15 People watching this product now!
Description

Heat Resistant Silicone Mat for Mobile Repair Benches

A heat resistant silicone mat for mobile repair does more than cover a table. The 2UUL ST83 gives you a defined 400 x 280 mm work zone where hot air, soldering irons and freshly heated boards rest without scorching your bench. 2UUL makes the ST83 from silicone that insulates heat up to 500°C. A surface treatment sold as an anti-dust coating helps keep fine debris off the mat during board-level work. If your shop runs a hot air station and a soldering station every day, this pad absorbs the heat and flux that would otherwise mark your counter.

Technical Highlights of the ST83 Silicone Pad

The ST83 measures 400 x 280 mm, which leaves room for a mainboard, a PCB holder and a small tray of screws side by side. The body uses high-grade silicone that resists corrosion, so flux, IPA and cleaning agents do not break the surface down. The top absorbs stray solder and protects your iron tip when you rest it, and the soft texture holds boards without scratching them. The 500°C rating keeps routine IC removal and reflow temperatures comfortably inside the pad’s limit. Cleaning takes one wipe with banana oil or a panel cleaner, which lifts flux residue and sticky marks between jobs. You can position the pad under a microscope or beside a hot air station and keep one clean zone for every board.

Where the Pad Fits in Your Repair Workflow

Every dead phone, charging issue or hang on logo fault that reaches your bench ends up as a hardware fault on a bare board, and that board needs a safe place to sit. Lay the mainboard on the ST83 before you start IC change karna with a hot air station, before you reball a BGA chip, or before you run a jumper lagana fix on a damaged track. The mat keeps heat off your bench top and gives you one clean place to stage screws and flex cables. During eMMC or UFS work, the same surface holds your ISP pinout board, adapter and test points while you solder fine wires. Pair it with a multimeter for continuity checks, a test box for software jobs and a microscope for inspection, and the whole repair sequence stays on one surface. The listing data for the ST83 confirms heat resistance and an anti-dust coating. It does not state an ESD rating, so keep your wrist strap on for static-sensitive boards.

Why Technicians Choose a Dedicated Silicone Pad

Many benches still use a folded cloth, a cardboard sheet or bare laminate under the hot air gun. Those surfaces scorch, soak up flux and shed lint onto the board. A dedicated silicone pad is a small purchase next to the bench damage it prevents, and it gives every technician in a service centre the same clean starting point for each job. Repair counters in Pakistan’s mobile markets run tight, and a 400 x 280 mm pad fits most bench layouts without crowding your tools. For shop owners, the ST83 works as a standard-issue accessory: buy one per bench, wipe it each evening and replace it when the surface wears out. If you are building a full setup, start with the pad, then add a hot air station, a soldering station, PCB holders and a reballing kit as your workload grows.

Additional information
Weight0.65 kg
Q & A
Please login to post questions

Key Features

  • Insulates heat up to 500°C
  • 400 x 280 mm working surface
  • Anti-dust coating
  • Absorbent surface that protects the solder tip and workbench
  • Corrosion-resistant high-grade silicone
  • Soft texture that holds boards without scratching
  • Cleans with banana oil or panel cleaner
  • Grey finish

Specifications

Brand2UUL
ModelST83
CategorySilicone Repair Mats / Mobile Repair Accessories
CompatibilityUniversal work surface, not device-specific
Supported DevicesUniversal, not device-specific
TechnologyHeat-resistant silicone with anti-dust coating
MaterialSilicone
Dimensions400 x 280 mm

Common Repair Uses

  • Supporting boards during IC change karna with hot air
  • Reballing BGA chips
  • Charging port and charging IC repair
  • Display problem and flex connector repair
  • eMMC and UFS ISP wire soldering on dead phones
  • Jumper lagana on damaged tracks
  • Board cleaning with IPA and flux removal
  • Staging screws, shields and small parts at the bench

Compatible Devices

  • Universal work surface for any phone board, not tied to a specific model or chipset
  • Android mainboards (Samsung, Oppo, Vivo, Infinix, Tecno and similar brands)
  • iPhone logic boards
  • Qualcomm and MediaTek based boards
  • Tablet and smartwatch boards
  • Detached LCD and flex assemblies
  • Standalone ICs, eMMC and UFS chips during rework
  • Hot air stations and soldering stations
  • PCB holders and ISP pinout boards

FAQ

What is the product name?
The product name is 2UUL ST83 Heat Resisting Silicone Pad with Anti Dust Coating.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is ST83.
What is this product used for?
This product is used as a heat-resistant work surface for mobile repair, soldering and hot air rework.
Which devices are compatible with this product?
This product is a universal work surface and works with any phone board or component. It is not tied to specific models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What temperature can the 2UUL ST83 silicone pad handle?
2UUL specifies heat insulation up to 500°C, which covers normal hot air and soldering iron temperatures used in mobile repair. Keep the hot air nozzle on the board, not on the mat.
Is the 2UUL ST83 an ESD anti-static mat?
The ST83 specifications confirm heat resistance and an anti-dust coating. They do not state an ESD rating, so use a separate ESD wrist strap or mat for static-sensitive work.