QianLi iPinch 360° Turntable Universal PCB Fixture
₨ 1
QianLi iPinch 360° PCB Fixture
The QianLi iPinch PCB holder clamps phone motherboards and chips up to 54mm wide and rotates them through a controllable 360° turntable. A chuck drive structure with silent needle roller bearings keeps the jaw movement smooth, while the heat-resistant synthetic stone body sits safely beside your hot air station. Built-in chip storage slots keep removed ICs within reach, and the compact 8.7 x 8.7 x 3.3 cm footprint leaves space for your microscope and soldering station. Use it for IC removal, glue cleaning, and micro soldering on dead phone and hardware fault boards. Mechanicpk supplies it for Pakistani repair shops that want a universal board holder.
Out of stock
QianLi iPinch PCB Holder With 360° Turntable
The QianLi iPinch PCB holder gives your micro soldering bench a rotating chuck fixture built for one job: keeping a phone motherboard or bare chip steady while you work on it. A 360° controllable turntable lets you swing the board to any angle without lifting it, and the chuck clamps boards and chips up to 54mm wide. If you handle IC change karna, glue removal, and hot air rework every day, this fixture replaces improvised clamps, tape, and a second pair of hands. It fits benches that already run a hot air station and a microscope and need a dependable board holder next to them.
Turntable and Chuck Mechanics
The iPinch combines a chuck drive structure with a controllable 360° turntable. You clamp the board, then rotate the whole assembly to reach the edge, corner, or chip position you need. The chuck movement runs on silent needle roller bearings, so the jaws slide smoothly and settle without the grinding feel of cheaper sliding clamps. The clamp range covers motherboards and chips up to 54mm wide, which suits phone logic boards, split board halves, and standalone chips. Boards wider than 54mm fall outside that range, so measure your board before you plan a job around this fixture. Within that limit, the iPinch works as a universal holder rather than a model-specific jig, so you do not buy a new fixture each time a new phone lands on your bench. Chips mount in the chuck too, which helps when you rework a removed chip on its own: clamp it, rotate it, and inspect each side before reballing.
Bench Workflow Fit
Rotation changes how you work around a board. When you remove an IC with your hot air station, you turn the board so the airflow reaches the chip from the cleanest direction, then rotate again to clean pads without releasing the clamp. Under a microscope, you angle the board toward your line of sight instead of leaning over it. The same setup helps with glue removal around chips, where you scrape and clean from several directions.
Technicians who chase dead phone, charging issue, and display problem faults at IC level repeat the same loop: secure the board, heat, lift, clean, replace. A fixture that stays put through each step shortens that loop and keeps your hands away from neighboring components. When a hang on logo or boot loop issue traces back to a damaged IC, repeatable board access matters even more.
Built-in chip storage slots hold small ICs and removed components within reach, so you stop chasing parts across the bench. At 8.7 x 8.7 x 3.3 cm, the iPinch takes little space beside a soldering station, a multimeter, and a reballing kit.
Why the QianLi iPinch PCB Holder Suits Pakistani Repair Benches
The iPinch body uses synthetic stone, which the product listings describe as heat resistant. That makes it a sensible choice next to hot air and soldering work. The unit comes in black and carries the QianLi name, a brand repair shops already associate with board-level tooling. Pair it with an ISP or eMMC programmer for dead-after-flash boards and a microscope for pad inspection, and you build a complete micro soldering station around it.
Shop owners who equip several benches get the same board positioning at every station, which keeps results consistent across technicians. Training institutes also benefit, because a fixed holder teaches safer habits than hand-holding a hot board. If you work on boards within the 54mm width limit, the iPinch earns its bench space quickly.
| Weight | 0.15 kg |
|---|
Key Features
- ✓360° controllable turntable
- ✓Chuck drive structure
- ✓Clamps motherboards and chips up to 54mm wide
- ✓Silent needle roller bearings in the chuck movement
- ✓Heat-resistant synthetic stone body
- ✓Built-in chip storage slots
- ✓Compact 8.7 x 8.7 x 3.3 cm footprint
- ✓Black finish
Specifications
| Brand | QianLi |
|---|---|
| Model | iPinch |
| Category | PCB Holder / Motherboard Fixture |
| Compatibility | Mobile phone motherboards and chips up to 54mm wide |
| Supported Devices | Universal — not device-specific |
| Technology | 360° controllable turntable with chuck drive structure and silent needle roller bearings |
| Material | Synthetic stone |
| Dimensions | 8.7 x 8.7 x 3.3 cm |
Common Repair Uses
- ✓Micro soldering, IC rework, and glue removal on phone motherboards
- ✓Micro soldering on phone motherboards
- ✓IC removal and replacement with a hot air station
- ✓Glue removal around chips and board edges
- ✓Pad cleaning after IC removal
- ✓Removed chip handling before reballing
- ✓Microscope inspection from multiple angles
- ✓Hardware fault diagnosis on dead phone boards
- ✓Board positioning during training sessions
Compatible Devices
- ✓Universal fixture for mobile phone motherboards and chips up to 54mm wide — not device-specific
- ✓Mobile phone motherboards up to 54mm wide
- ✓Standalone chips and ICs up to 54mm wide
- ✓Android phone logic boards within the width limit
- ✓iPhone logic boards within the width limit
- ✓Split upper and lower board layers within the width limit
- ✓Bare PCBs removed from phones
- ✓Small repair boards within the width limit
- ✓Boards wider than 54mm fall outside the clamp range
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the maximum board width the QianLi iPinch can hold?
Can I use the QianLi iPinch with a hot air station for IC removal?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



