Relife Glue Squeezer for Mobile Repair Pakistan

₨ 650

Manual Syringe Glue Squeezer

The Relife glue squeezer for mobile repair Pakistan gives your bench a manual push-rod dispenser for syringe-based materials. You load a syringe of UV solder mask oil, solder paste, flux, or structural adhesive, squeeze the ergonomic handle, and the plunger pushes out a steady, controllable bead. It needs no power, no air line, and no setup time. Technicians use it for board-level coating, pad work, and frame or screen sealing, wherever thumb pressure on a bare syringe wastes material or floods the joint. Match it to the syringe size your bench already runs and add it to your repair consumables kit.

In stock

14 People watching this product now!
Description

Relife Glue Squeezer for Precise Syringe Dispensing at the Repair Bench

If you do board-level work, you know how fast a bare syringe turns into a mess. The Relife glue squeezer for mobile repair Pakistan fixes that with a manual push-rod mechanism that converts one hand squeeze into steady plunger pressure. You dispense UV solder mask oil, solder paste, flux, or structural adhesive in a controlled bead, with no compressor, no power cord, and no dispensing controller. Whether your shop handles dead phone boards, charging issue jobs, or screen resealing, this squeezer replaces uneven thumb pressure with a mechanism that delivers consistent force from the first press to the last drop in the barrel.

Why the Relife Glue Squeezer Suits Mobile Repair Work in Pakistan

Relife builds its manual glue squeezer range around a push-rod drive and a handle shaped for a comfortable, even grip. That layout matters on a repair bench, where you hold a syringe for minutes at a time and need a steady hand over a fine pad or a trace. The squeezer spreads force evenly along the plunger, so thick materials like solder paste and structural adhesive leave the needle smoothly instead of in bursts.

The range covers several syringe sizes. The RL-062C takes 3-5cc syringes for pad-level work, the RL-062A takes 10cc syringes, and the RL-062B takes 30-60cc syringes for technicians who go through flux or mask oil quickly. Most configurations include two needles in different specifications, so you switch between a fine bead and a wider flow without hunting for accessories. The tool is reusable, which keeps your running cost on the syringe and the material, not on the dispenser.

Where It Fits in Your Repair Workflow

On a typical hardware fault job, you diagnose with a multimeter, lift the suspect IC with a hot air station, clean the pads, and rebuild. The squeezer enters at the rebuild stage. When you do IC change karna on a charging or power section, you lay flux or solder paste on the pads through the needle before you place the chip, and you control the amount with the handle instead of guessing with your thumb. After a trace repair or jumper lagana job, you seal the exposed copper with UV solder mask oil and cure it. As a UV solder mask oil dispenser, the squeezer keeps that coat thin and even.

Frame and screen work uses the same tool. Structural adhesive for sealing screen structures flows out of a 10cc or 30-60cc syringe under steady pressure, so you avoid squeeze-out along the edges. Pair the squeezer with soldering stations, hot air stations, a microscope for pad-level inspection, and PCB holders that keep the board still, and it becomes the dispensing step in a complete bench setup. If you reball BGA chips, keep it next to your reballing kits for paste and flux.

Choosing the Right Size and Loading the Syringe

Match the squeezer to the syringe your bench already uses. Choose the 3-5cc variant if you mostly place paste on small pads under a microscope. Choose the 10cc variant for everyday flux and mask oil. Choose the 30-60cc variant if your shop runs high-volume resealing or coats several boards a day. If your volume grows, you step up to the larger variant and keep the same materials.

Loading takes seconds. On most variants, you push the metal buckle on the handle upward, pull the plunger all the way back until its head locks, then seat the syringe in the mounting slot. Cap the needle after each job and wipe the barrel before you store the tool, so your next hardware fault repair starts with a clean dispenser.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • Manual push-rod drive that needs no power or air supply
  • Ergonomic handle for a comfortable, even grip
  • Steady plunger force for smooth, controlled flow
  • Dispenses UV solder mask oil, solder paste, flux, and structural adhesive
  • Available in variants for 3-5cc, 10cc, and 30-60cc syringes
  • Most configurations include two needles in different specifications
  • Reusable tool that cuts dispenser running cost
  • Quick syringe loading with a buckle and plunger lock

Specifications

BrandRelife
CategoryRepair Consumables – Glue and Dispensing Tools
CompatibilitySyringe-based materials – UV solder mask oil, solder paste, flux, structural adhesive
TechnologyManual push-rod drive

Common Repair Uses

  • Board-level material dispensing and frame or screen sealing in the mobile repair workflow.
  • Applying UV solder mask oil over repaired traces
  • Sealing exposed copper after jumper lagana
  • Dispensing solder paste onto pads before SMD placement
  • Laying flux on pads before IC change karna
  • Board-level SMD repair on dead phone boards
  • Dispensing structural adhesive for screen structure sealing
  • Frame sealing during screen repair
  • Controlled paste and flux dispensing during charging issue repairs

Compatible Devices

  • Universal – not device-specific. The squeezer dispenses material onto any phone board or frame, and it fits syringes by size rather than by phone model.
  • 3-5cc syringes (RL-062C variant)
  • 10cc syringes (RL-062A variant)
  • 30-60cc syringes (RL-062B variant)
  • UV solder mask oil syringes
  • Solder paste syringes
  • Flux syringes
  • Structural adhesive syringes
  • Boards and frames from any brand, including Samsung, Oppo, Vivo, Infinix, Tecno, and iPhone

FAQ

What is the product name?
The product name is Relife Glue Squeezer.
What is the brand of this product?
The brand of this product is Relife.
What is this product used for?
This product is used for dispensing UV solder mask oil, solder paste, flux, and structural adhesive from syringes during mobile phone board and screen repair.
Which devices are compatible with this product?
This product is universal and not device-specific. It dispenses onto boards and frames from any phone brand and fits syringes by size.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which syringe sizes does the Relife glue squeezer support?
The Relife RL-062 series covers three syringe ranges. The RL-062C takes 3-5cc, the RL-062A takes 10cc, and the RL-062B takes 30-60cc syringes.
Can I use it for UV solder mask oil and solder paste on a dead phone board?
Yes. The squeezer suits UV solder mask oil, solder paste, flux, and structural adhesive in syringes, so you can use it for trace sealing and pad work on dead phone boards.