Relife XA5 Inductance Tester for Mobile Motherboards
₨ 500
USB-C Inductance Tester for Phone Boards
The Relife XA5 inductance tester gives your repair bench a fast way to check coil health on mobile phone motherboards. It uses electromagnetic induction to test inductors in place, so you isolate a hardware fault before you pick up a hot air station. A green light signals a healthy inductor. The 76 × 27 × 6 mm body weighs 3.6 g and runs on 5V through USB-C, so you can keep one at every workstation. Technicians chasing a dead phone, a charging issue or a boot loop issue use it to narrow down the failed coil first. Mechanicpk supplies it to repair shops across Pakistan.
In stock
Relife XA5 Inductance Tester: Coil Fault Isolation for Phone Boards
The Relife XA5 inductance tester does one job on the repair bench: it confirms whether an inductor on a mobile phone motherboard still works. Power-section faults leave you with a long list of suspect parts, and buck coils sit near the top of that list. The XA5 checks a coil in place through electromagnetic induction, so you scan the board instead of lifting components one by one. It takes 5V over USB-C and has no internal battery to replace. Its plug-in operation lets any technician in the shop connect it and start testing right away. For buyers who already know their inductors, the XA5 works as a fast screening step before measurement and rework.
How the Electromagnetic Induction Check Works
The tester detects the inductor through electromagnetic induction instead of probes that need solid contact on the pads. You move the tip over the component you suspect, and the XA5 shows a green light when it detects a healthy inductor. A coil that fails to trigger the light deserves a closer look with your multimeter or a bench LCR instrument when you need a numeric value. This approach protects the board. You do not desolder the coil, you do not heat the neighbouring parts, and you do not risk lifting a pad just to learn the coil was fine. The 76 × 27 × 6 mm body and 3.6 g weight let you work around tightly packed power sections under a microscope without the tester crowding your view.
Where the Relife XA5 Inductance Tester Fits in Your Repair Workflow
A dead phone, a charging issue or a hang on logo fault often traces back to the power section, so the coil check belongs early in the diagnosis. Start with a visual inspection under the microscope. Then run the XA5 over the buck coils and other inductors on the affected rail. Mark every coil that fails to show the green light, confirm it with the multimeter, and only then decide between coil replacement and IC change karna. Workshops that handle boot loop issue boards in volume save the most time here, because the tester shortens the target list before anyone touches a soldering station. Pakistani repair shops, service centers and training institutes get a repeatable first test that a new technician learns in minutes. The listed compatibility also covers laptop and PC motherboards, so the same tester serves your wider board-level work.
Pairing the XA5 with the Rest of Your Bench
Treat the XA5 as the first hardware gate in a longer diagnostic chain. Coils that pass the check send you on to the multimeter for rail and short-circuit measurements and back to the microscope for visual confirmation of cracked or burnt bodies. When a board stays dead after the power section checks out, you move to the data side. ISP pinout tools, eMMC programmers, UFS adapters and test boxes cover software marna and dead after flash recovery. When the XA5 does flag a bad coil, you remove it with a hot air station and fit the replacement with a soldering station. A PCB holder keeps the board steady during that work, and reballing kits support any BGA job nearby. If you currently test coils by guesswork, the XA5 gives you a consistent first pass. If you need exact inductance values, keep a multimeter or LCR meter alongside it.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Electromagnetic induction testing of inductors on the board
- ✓Non-contact check with no component removal
- ✓Green light indicates a healthy inductor
- ✓5V USB-C power with no internal battery
- ✓Plug-in operation for quick setup at any bench
- ✓Compact 76 × 27 × 6 mm body for tight board areas
- ✓3.6 g weight for easy handling and portability
- ✓Suited to mobile phone, laptop and PC motherboard coil checks
Specifications
| Brand | Relife |
|---|---|
| Model | XA5 |
| Category | Inductance Tester / Mobile Motherboard Repair Tool |
| Compatibility | Mobile phone, laptop and PC motherboards (universal, not device-specific) |
| Supported Devices | Mobile phone motherboards and PCB boards |
| Technology | Electromagnetic induction |
| Input Voltage | 5V (USB-C) |
| Dimensions | 76 × 27 × 6 mm |
| Weight | 3.6 g |
Common Repair Uses
- ✓Inductor and buck coil testing during board-level mobile repair
- ✓Checking inductors in place without desoldering
- ✓Isolating the faulty coil on a dead phone board
- ✓Power-section checks on a boot loop issue board
- ✓Coil checks during charging issue diagnosis
- ✓Screening suspect coils before IC change karna or coil replacement
- ✓Coil checks on laptop and PC motherboards
Compatible Devices
- ✓Universal board-level scope — mobile phone, laptop and PC motherboards (not tied to specific phone models)
- ✓Mobile phone motherboards (universal)
- ✓Laptop motherboards
- ✓PC motherboards
- ✓General PCBs with SMD inductors and buck coils
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the Relife XA5 need a battery or an adapter?
Can I test an inductor with the XA5 without desoldering it?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



