YCS 3S UV Curing Green Mask for PCB & BGA Repair

₨ 500

UV Curing Green Oil for PCB Repair
YCS 3S UV Curing Green Mask is a 10cc syringe of UV-curable green solder mask oil built for motherboard repair. Apply a thin layer over scratched traces, exposed copper, rebuilt pads or fixed jumper wires, then cure it under UV light. The supplier lists a cure time of about three seconds, so your board leaves the bench faster after a BGA IC job or a charging port repair. The cured layer insulates the repair zone and finishes smooth, which keeps the fix tidy under a microscope. Pakistani technicians reach for this UV curing green oil for mobile repair whenever a clean, insulated finish matters.

Out of stock

10 People watching this product now!
Description

YCS 3S UV Curing Green Mask for Precise PCB Insulation

The YCS 3S UV Curing Green Mask gives you a 10cc syringe of UV-curable green solder mask oil for rebuilding the protective layer on a motherboard after rework. If you search for UV curing green oil for mobile repair, this is the consumable that closes the job once the IC change, jumper wire or pad repair is finished. The oil stays liquid until UV light reaches it, so you control placement, thickness and timing before you lock the result in place. The supplier lists a cure time of roughly three seconds, which keeps boards moving on a busy repair bench.

How the 3S Formula Behaves on the Bench

UV curing oil needs ultraviolet light to harden, so it never sets while you position it. You lay a thin bead, clear the pad edges with a toothpick or needle, and then expose it to your UV lamp. Suppliers describe the cured layer as an electrical insulator with a smooth finish that leaves repair marks hard to spot. They also describe the oil as suited to high-temperature environments and prolonged use, but no numeric heat rating exists in the published data. Treat it as a post-rework coating: finish all hot air and soldering work first, then apply the oil. The green shade matches the standard mask colour on many boards, so you can judge coverage at a glance.

Where It Fits in the Mobile Repair Workflow

This product belongs at the end of the PCB repair process. After you reball a BGA chip with a reballing kit, replace a charging IC, or lay a jumper wire across a broken trace, the exposed copper and bare pad edges need insulation. Clean the area, confirm continuity with your multimeter, and only then coat the repair. That order protects you from sealing a hardware fault under the mask. The same step helps on dead phone boards that need several rework passes, because the coating keeps repaired pads from lifting during handling. Pair the oil with a stable soldering station, a hot air station for the rework stage, a microscope for placement, and a PCB holder that keeps the board still while the oil cures.

Practical Use of the 10cc Syringe

The syringe holds 10cc and weighs about 25g, with listed dimensions of 19 x 95 x 34 mm, so it fits a bench drawer or a technician’s kit tray without trouble. Squeeze out only what the repair needs. A small amount covers a jumper wire junction or a single rebuilt pad, and a tiny excess wipes away before you cure it. You need a separate UV light source for hardening, and UV-blocking eye protection keeps your eyes safe during exposure. Close the syringe and store it away from direct light between jobs, since stray UV exposure can start the cure before you want it.

Why Technicians Choose a Dedicated Green Mask Oil

Charging issue boards, display problem boards and network issue boards all share one trait: the repair area ends up with disturbed solder mask. A dedicated green oil restores that layer instead of leaving bare copper exposed. Shops that run daily BGA and jumper work finish each board with a consistent, insulated look. For the workshop owner, one syringe serves dozens of repairs, which keeps the cost per job low and the finish quality steady across your whole team.

Additional information
Weight0.25 kg
Q & A
Please login to post questions

Key Features

  • 10cc syringe of green UV-curable solder mask oil
  • Supplier-listed cure time of about three seconds under UV light
  • Electrically insulating cured layer for exposed copper and pads
  • Smooth finish with inconspicuous repair marks
  • Described as suited to high-temperature environments and prolonged use
  • Built for mobile phone PCB chip repair, BGA IC repair and jumper wire repair
  • Compact 19 x 95 x 34 mm syringe pack at roughly 25g
  • Green colour that matches standard motherboard mask for easy inspection

Specifications

Brand EntityYCS
Product EntityYCS 3S UV Curing Green Mask (UV solder mask green oil, 10cc)
Technology EntityUV-cured solder mask, ultraviolet curing
Compatible Device EntitiesSmartphone motherboards, iPhone logic boards, general electronics PCBs
Repair Process EntitySolder mask restoration, BGA rework protection, jumper wire insulation
Industry EntityMobile phone repair, PCB repair, GSM repair workshops in Pakistan

Common Repair Uses

  • Verified mobile PCB and BGA rework scenarios
  • Restoring scratched or peeled solder mask
  • Insulating exposed copper after IC removal
  • Securing and insulating jumper wires
  • Protecting repaired traces from shorts
  • Covering rebuilt pads after tinning
  • Sealing the rework zone after BGA reballing
  • Protecting charging port pad repairs
  • Finishing hardware fault repairs on dead phone boards

Compatible Devices

  • Universal PCB solder mask oil, not device-specific
  • Android smartphone motherboards
  • iPhone logic boards
  • BGA chip areas on mobile phone PCBs
  • Charging port pad and trace repair zones
  • Jumper wire routes on repaired motherboards
  • Tablet motherboards
  • Smartwatch and wearable PCBs
  • General electronics circuit boards

FAQ

What is the product name?
The product name is YCS 3S UV Curing Green Mask.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is 3S Green.
What is this product used for?
This product restores and insulates solder mask on mobile phone PCBs after BGA, IC, pad and jumper wire repair.
Which devices are compatible with this product?
This product is a universal PCB solder mask oil, so it works on smartphone motherboards and general circuit boards rather than specific phone models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How long does YCS 3S green oil take to cure under UV light?
The supplier lists a cure time of about three seconds under UV light. Actual time depends on your lamp strength and layer thickness, so cure thin layers and check that the surface feels hard.
Can I use YCS 3S green mask before hot air rework?
Apply it after rework. The supplier describes the oil as suited to high-temperature environments, but no numeric temperature rating is published, so finish your hot air and soldering work first and coat the area last.