UMP510G Power IC for Unisoc Mobile Repair
₨ 250
H2: UMP510G Power IC for Unisoc Mobile Repair
The UMP510G power IC is a BGA power management IC for Unisoc-based phones, including Motorola Moto G20 and E20, Realme C30, C31 and C35, Samsung SM-A035 series, and Itel Vision 3 Plus boards. You replace it when a dead phone, charging issue, or boot loop issue traces back to a failed PMIC. Pair it with a hot air station, a microscope, and a reliable bench power supply to diagnose the fault, swap the IC, and verify stable current draw before you close the phone. Check the marking on your board before you order.
H2: UMP510G Power IC for Unisoc Phone Repair
The UMP510G power IC is a BGA-packaged power management IC from the Unisoc (Spreadtrum) ecosystem. It sits on the mainboard of Unisoc-based phones from Motorola, Realme, Samsung, Itel, Tecno, and Infinix. When this IC fails, the board loses the regulated rails that the processor, memory, and peripherals depend on, so the phone stops behaving like a phone. If you handle dead phone and charging jobs on budget Unisoc boards, you meet this fault regularly, and a stocked UMP510G power IC shortens your turnaround.
H3: What the UMP510G handles on the board
A power management IC takes the battery and charger input and turns it into the separate voltage rails that the processor, memory, display, and peripherals need. On Unisoc platforms, the PMIC also controls power sequencing during startup, so a weak or shorted IC stops the boot process before the logo appears. You usually spot this on the bench: the phone draws no current, draws too much current, or draws a steady amount and never wakes up. The UMP510G fills that role on the Motorola, Realme, Samsung, and Itel models listed below. Treat it as a board-level component, not a plug-in module.
H3: Where the UMP510G fits in your repair workflow
Start with diagnostics. Connect a DC power supply, read the current draw, and check the main rails with a multimeter. If a rail shorts to ground, freeze spray or a thermal camera shows you which component heats up first. When the PMIC runs hot or the readings point to it, move to rework. Hold the board on a PCB holder, apply flux, and lift the IC with a hot air station set to a profile that matches your solder alloy. Clean the pads under a microscope, place the new UMP510G with the correct orientation, and reflow it evenly. Finish with a power-on test: confirm a normal idle current, then test charging before you reassemble the phone. If you rework BGA parts daily, a preheater-equipped rework station is the natural upgrade from a basic hot air gun.
H3: BGA replacement notes for technicians
The UMP510G ships in a BGA package, so you cannot inspect the joints after placement. Preheat the board to protect neighboring components, keep the airflow steady, and shield nearby connectors and flex sockets. Check the underside of the replacement IC and the board pads for debris before you place it. Align the IC by its marking and pad pattern, then let the solder self-center as it reflows. Avoid pressing the IC down while the solder is liquid, because you can bridge adjacent balls. If the phone still fails after the swap, recheck the surrounding capacitors, the battery connector, and the charging path before you blame the new part.
H3: Compatibility checks before you order
Distributor listings tie the UMP510G power IC to Unisoc-based phones from Motorola, Realme, Samsung, Itel, Tecno, and Infinix. Model coverage differs by brand, so read the PMIC marking on your own board and compare it with this part before you order. Do not assume a MediaTek or Qualcomm board accepts this IC, because those platforms use different power management parts. Keep a few pieces in stock if your shop sees repeat Unisoc boards. A single IC change karna job can clear a dead phone, charging issue, or boot loop fault without a full board swap, and your repair bench keeps moving.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Unisoc (Spreadtrum) power management IC for mobile phone boards
- ✓BGA package for compact mainboard layouts
- ✓Listed for Motorola Moto G20 and E20 boards
- ✓Listed for Realme C30, C31, and C35 boards
- ✓Listed for Samsung SM-A035 series and Itel Vision 3 Plus boards
- ✓Suits hot air and BGA rework with correct preheating
- ✓Replaces a failed PMIC in dead phone, charging, and boot loop repairs
- ✓Built for technicians who handle micro-soldering and board-level repair
Specifications
| Brand | Unisoc (Spreadtrum) |
|---|---|
| Model | UMP510G |
| Category | Mobile Phone Power Management IC |
| Compatibility | Unisoc-based Motorola, Realme, Samsung, Itel, Tecno, and Infinix phones |
| Supported Devices | Motorola Moto G20 (XT2128), Moto E20 (XT2155), Realme C30, C31, C35, Samsung SM-A035 series, Itel Vision 3 Plus |
| Technology | Power management IC (PMIC) |
| Package | BGA |
Common Repair Uses
- ✓Scope: PMIC-related faults on Unisoc-based phone boards.
- ✓Dead phone with no current draw on the bench power supply
- ✓Excess current draw or a short on the main power line
- ✓Charging issue where the phone does not detect or accept a charger
- ✓Boot loop issue where the rails drop during startup
- ✓Hang on logo caused by unstable supply rails
- ✓PMIC overheating found with a thermal camera or freeze spray
- ✓Liquid-damaged boards with corroded PMIC pads
- ✓IC change karna after you confirm the PMIC as the faulty part
Compatible Devices
- ✓Scope: Unisoc-based phone boards. Confirm the PMIC marking on your board before ordering.
- ✓Motorola Moto G20 (XT2128)
- ✓Motorola Moto E20 (XT2155)
- ✓Realme C30
- ✓Realme C31
- ✓Realme C35
- ✓Samsung SM-A035 series
- ✓Itel Vision 3 Plus
- ✓Selected Tecno and Infinix Unisoc models (verify on-board marking)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I confirm the UMP510G is the faulty part on a dead phone?
Does the UMP510G work on MediaTek or Qualcomm boards?
Related products
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



