MECHANIC 530 Electronic Contact Cleaner Spray 550ML
₨ 700
550ml Electronic Contact Cleaner Spray for PCB and Connector Cleaning
The MECHANIC 530 is a 550ml aerosol contact cleaner for cleaning PCBs, connectors, switches and small electronic parts. Its solvent-and-surfactant formula removes dust, light oxidation and flux residue, and it evaporates quickly, so the board is ready for inspection soon after cleaning. The spray pattern helps you reach tight spaces around board-level components. For a repair bench that handles mobile boards every day, a 550ml can gives you enough volume for regular cleaning across many jobs.
Out of stock
Electronic Contact Cleaner Spray for Precision Board Cleaning
An electronic contact cleaner spray belongs on every repair bench that handles board-level work. The MECHANIC 530 is a 550ml aerosol built for cleaning contacts, connectors and PCB surfaces before you inspect, solder or reball. You get a fast-evaporating formula that removes dust, grease film and light oxidation without leaving a visible residue. Use it at the cleaning stage of your workflow, before the diagnostic or repair steps begin.
Where It Fits in Your Board-Level Workflow
Most board-level jobs start with a dirty surface. Dust, old flux and oily film can hide a cold joint or block a clean probe contact during testing. Spray the affected area, let the solvent lift the residue, and then clean the surface with a brush before you check the board under a microscope. You then start diagnosis with a clean baseline, which makes measurements with a multimeter more reliable. The same step prepares the board for reballing or rework, where leftover residue can interfere with new solder.
Cleaning Scope on Boards, Connectors and Contacts
The spray works on the surfaces technicians clean most often. Charging port pins, FPC connector contacts, switch terminals and SIM tray contacts all collect dirt and oxidation over time. Aim the nozzle at the contact area and keep the can upright while spraying. Spray in short bursts rather than one long stream, so you cover the area without flooding nearby components. Brush the contact lightly while the solvent works, then let the connector dry before you reconnect power or inspect the result.
Handling Notes for Clean, Safe Results
Power off the device and disconnect the battery before you start any cleaning job. Spray in a ventilated area, because the solvent vapor builds up quickly in a closed room. Keep the can away from heat sources, direct sunlight and open flames, and store it upright. Allow the board to dry fully before you apply heat, power or any test probe, since trapped moisture or solvent can cause unexpected readings. A soft brush and a clean lint-free cloth complete the job, and these items sit well beside your PCB holder and microscope on the bench.
| Weight | 0.5 kg |
|---|
Key Features
- ✓550ml aerosol volume for regular repair bench use
- ✓Hydrocarbon-based solvent with surfactant formula
- ✓Fast evaporation for quick return to inspection
- ✓Removes dust, light oxidation and oily film
- ✓Spray pattern suited to tight board-level areas
- ✓Works on PCBs, connectors and electronic contacts
- ✓Suitable for pre-reballing and post-rework cleaning
- ✓Compact can for bench storage
Specifications
| Model | 530 |
|---|---|
| Category | Electronic Contact Cleaner Spray |
| Technology | Hydrocarbon-based solvent with surfactant |
| Volume | 550ml |
Common Repair Uses
- ✓Cleaning boards before microscope inspection
- ✓Removing light flux and solder residue before reballing
- ✓Cleaning oxidized charging port pins
- ✓Removing dust from FPC connector contacts
- ✓Clearing residue after hot air rework
- ✓Cleaning switch and keypad contacts
- ✓Preparing board surfaces before multimeter testing
- ✓General cleaning of electronic assemblies on the repair bench
Compatible Devices
- ✓Universal, not device-specific. Suitable for any electronic board or contact surface.
- ✓Mobile phone motherboards and PCBs
- ✓Charging port and USB connector pins
- ✓FPC and board-to-board connector contacts
- ✓SIM tray and audio jack contacts
- ✓Switch and keypad contacts
- ✓Laptop and console boards
- ✓Small electronic parts and metal contacts
- ✓Repair bench tools such as PCB holders and tweezers
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can this spray be used before reballing a chipset?
Is it safe to spray on a powered device?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



