BS-02 Steel Brush for BGA CPU Cleaning (2 Pcs)
₨ 1,200
BS-02 Dual-Head BGA Cleaning Brush
This steel brush for BGA cleaning gives you two working heads in one handle: a superfine steel wire side for stubborn glue and solder residue on IC pads, and a soft anti-static bristle side for dust and flux. The BS-02 ships as a 2-piece set, so you keep one brush at your hot air station and one at your PCB cleaning tray. Use it after IC change karna, before reballing a CPU, or whenever a motherboard needs a clean pad surface before the next soldering step. The compact, lightweight body gives you precise control on mobile phone and laptop boards.
In stock
Steel Brush for BGA Cleaning: BS-02 Dual-Head Pad Prep Tool
A clean pad decides whether a reballed chip sits flat or fails after the first heat cycle. This steel brush for BGA cleaning gives you a two-head BS-02 tool built for that job. A steel wire head scrubs hardened glue and solder residue, and a soft bristle head sweeps dust and flux off the board. Mechanicpk supplies the BS-02 as a 2-piece set, so one brush stays at your rework station and the second serves your cleaning tray or a second technician.
Steel Wire Head for Glue and Pad Residue
The metal side targets the residue that survives after you lift a chip. Old underfill glue, hardened flux and leftover solder cling to BGA pads and slow down every step that follows. The steel wire bristles cut through that layer faster than a cotton swab or a plastic brush. Apply light, even strokes across the pad area and let the bristles do the work. Heavy pressure lifts pads, so keep your hand relaxed and check the surface often. This head suits CPU, eMMC, NAND and power IC pads on mobile boards, as well as the larger pad fields on notebook motherboards.
Soft Bristle Head for Flux and Dust
The plastic bristle side handles the gentle work. Use it to sweep dust, flux residue and loose debris from around components without scratching the board. Distributors list the BS-02 as an anti-static double-sided brush, which makes the soft head a sensible choice for routine board cleaning near sensitive parts. The same head also cleans phone components, notebook keyboards and computer fans, so the brush earns its place outside the rework bench too.
Where It Fits in Your Rework Workflow
Pad cleaning sits between chip removal and reballing. A typical sequence on a dead phone or hardware fault board runs like this: you preheat the board, lift the chip with your hot air station, clear the bulk solder with wick, and then brush the pads with the steel head until the surface shows clean metal. You finish with the soft head to remove loose particles, inspect the pads under your microscope, and move to your reballing kit. A PCB holder keeps the board steady while you brush, which protects the pads from slipping strokes. The BS-02 turns that cleaning step into a quick, repeatable routine instead of a fiddly one.
Why a 2-Piece Set Suits Workshops
Repair shops rarely use one brush for every task. Glue-heavy work wears the steel head faster, and shared stations need their own tools. The 2-piece pack gives you a spare for busy weeks and keeps your cleaning tools next to your soldering stations instead of in a drawer across the room. The handle measures roughly 14 cm in length and 12 mm in thickness according to distributor listings, so it fits comfortably in a tool tray and works in tight board areas.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Dual-head design with one steel wire side and one soft bristle side
- ✓Superfine steel wire head for glue and residue removal on IC pads
- ✓Anti-static double-sided brush construction listed by distributors
- ✓2-piece set for multiple benches or spare stock
- ✓Compact, lightweight body for precise control
- ✓Reusable for repeated cleaning jobs
- ✓Suits mobile phone, notebook and computer PCB cleaning
- ✓Works alongside hot air stations, reballing kits, PCB holders and microscopes
Specifications
| Model | BS-02 |
|---|---|
| Category | PCB Cleaning Brushes |
| Compatibility | Mobile phone, notebook and computer PCBs, IC pads and BGA chip pads |
| Supported Devices | Universal, not device-specific |
| Material | Steel wire brush head, plastic bristle brush head |
| Dimensions | Approx. 14 cm length, 12 mm thickness |
Common Repair Uses
- ✓Pad cleaning and board cleaning tasks around hot air rework and reballing
- ✓Removing old glue from IC pads after IC change karna
- ✓Cleaning BGA pads before reballing a CPU
- ✓Scrubbing soldering residue and flux off a PCB
- ✓Dusting motherboards with the soft bristle head
- ✓Cleaning pads before fitting a replacement chip
- ✓Cleaning mobile phone components
- ✓Cleaning notebook keyboards
- ✓Cleaning computer fans
Compatible Devices
- ✓Universal cleaning tool for mobile phone and computer boards, not tied to a single model or chipset
- ✓Mobile phone motherboards
- ✓Laptop and notebook motherboards
- ✓Desktop computer PCBs
- ✓BGA chip pads
- ✓IC pads after chip removal
- ✓Mobile phone components
- ✓Computer keyboards
- ✓Computer cooling fans
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which side of the BS-02 brush removes glue from BGA pads?
Can I use the steel side on BGA pads without damaging them?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



