2UUL FX-0009 0.009mm Ultrafine Jumper Wire 100M

₨ 900

0.009mm Jumper Wire for Board-Level Repair

The 2UUL FX-0009 is a 0.009mm jumper wire built for micro-soldering on mobile phone and electronic motherboards. This 100M spool of bare, non-insulated ultrafine wire bridges broken traces, restores lifted IC pads, and repairs peeled CPU solder joints. The wire carries no breakpoints, resists magnetism, and flexes without snapping, so you route it between pads under the microscope without losing control. It tins easily and welds directly, which keeps your solder resistance low. Technicians across Pakistan use this ultrafine jumper wire for CPU, BGA, and fingerprint-circuit repair where thicker wire cannot fit.

In stock

20 People watching this product now!
Description

0.009mm Jumper Wire for Precision Mobile Board Repair

The 0.009mm jumper wire from 2UUL, model FX-0009, is the finest conductor in the brand’s 100-metre bare-wire range. At 0.009mm, it reaches pads and traces that thicker fly line cannot cover, so you restore broken connections on CPU, BGA, and fingerprint-circuit boards without disturbing neighbouring pads. Mechanicpk supplies the FX-0009 to technicians and repair shops across Pakistan who run board-level work every day. One 100-metre spool supplies a long run of jumpers, so a busy bench draws from it across many repair jobs.

Where the FX-0009 Fits on Your Repair Bench

Board repair starts with diagnosis. You trace the fault with a multimeter, find the open trace or lifted pad, and decide how to restore the connection. The FX-0009 handles the restoration step. After you remove the IC with a hot air station, clean the pads, and expose the damaged trace, you lay a short length of this wire from the intact pad to the next valid connection point and fix it with your soldering station.

This workflow applies to dead phone cases caused by broken traces, charging issue repairs where the pad near the connector lifted, and display problem jobs where a flex connector pad tore off. In each case, a thicker jumper wire either covers neighbouring pads or lifts the repair from the board. At 0.009mm, the wire sits flat and stays inside the pad footprint.

Handling and Soldering Behavior

Manufacturer and supplier listings describe the FX-0009 as bare, non-insulated wire with no breakpoints, no magnetism, good toughness, and low solder resistance. Each property matters at the bench. The continuous wire without breakpoints means you do not chase an invisible break after you finish a repair. The non-magnetic construction keeps the wire from pulling toward tweezers or magnetised tools while you position it.

The wire tins easily, so a light touch of solder with your iron tip wets the end and creates a joint without long dwell time. It welds directly onto the pad with no paint to scrape, which removes the enamel-stripping step that insulated wire demands. Less time on the pad means less thermal stress on the board, which protects the surrounding solder mask and nearby components.

Work under a microscope. At this diameter, the wire disappears to the naked eye, so magnification and a steady PCB holder separate a clean jumper from a lost one. Cut the length slightly longer than you need, tin one end, set it on the target pad, and then route the opposite end to the destination point before you cut and tin it.

Choosing FX-0009 Over Thicker Wire

The 2UUL range covers several diameters. The FX-0009 sits at 0.009mm, the FX-001 at 0.01mm, and the FX-002 at 0.02mm. The thicker options suit wider traces and larger pads. Pick the FX-0009 when the pad is tiny, the trace runs close to its neighbours, or the repair sits under a BGA package where height matters. Because the wire is non-insulated, route it so it cannot touch adjacent pads, and cover the finished repair with UV solder mask or glue where the layout requires protection.

Keep your reballing kit, flux, and cleaning supplies at hand for jobs that start with an IC removal and end with a jumper. Pair the wire with a precision soldering station set to a controlled temperature, and you complete pad and trace repairs that previously ended in a board replacement.

Why Technicians Pick It

Pakistani repair shops run on speed and success rate. Replacing a board costs the customer more and costs you the repair margin. A 0.009mm jumper wire turns many hardware fault jobs into billable repairs. The FX-0009 gives you the thinnest option from a known repair-wire brand in a spool length that lasts, so you stock one reel instead of reordering short lengths.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • 0.009mm ultrafine diameter for tiny pads and tight traces
  • 100M spool length for sustained workshop use
  • Bare, non-insulated wire
  • No breakpoints along the wire
  • Non-magnetic for easy positioning
  • Good toughness and flexibility
  • Low solder resistance
  • Easy to tin, direct welding, no paint scraping

Specifications

Brand2UUL
ModelFX-0009
CategoryJumper Wire (Ultrafine Fly Line)
CompatibilityUniversal, not device-specific
TypeNon-insulated
Dimensions0.009mm diameter, 100m length

Common Repair Uses

  • Board-level micro-soldering where a broken trace, lifted pad, or peeled solder joint needs a jumper
  • CPU solder joint peeling repair
  • BGA chip pad repair
  • IC chip pad restoration
  • Bridging components and IC chips
  • Broken PCB trace repair
  • Fingerprint circuit repair
  • Mobile phone motherboard repair
  • Tablet and electronic motherboard repair

Compatible Devices

  • Universal jumper wire for board-level repair, not tied to one model or chipset
  • Apple phone motherboards
  • Samsung phone motherboards
  • Huawei phone motherboards
  • Xiaomi phone motherboards
  • Google phone motherboards
  • Other mobile phone logic boards
  • Tablet motherboards
  • Computer and electronic PCBs

FAQ

What is the product name?
The product name is 2UUL FX-0009 Ultrafine Jumper Wire 0.009mm 100M.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is FX-0009.
What is this product used for?
This product is used for micro-soldering repairs such as broken PCB traces, lifted IC pads, and peeled CPU solder joints.
Which devices are compatible with this product?
This product is a universal jumper wire for mobile phone, tablet, and computer motherboards, so it is not tied to one specific model.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the 2UUL FX-0009 insulated or bare wire?
The FX-0009 is non-insulated bare wire. It has no enamel coating, so you solder it directly without scraping paint, and you keep it away from adjacent pads.
What is the difference between FX-0009, FX-001, and FX-002?
The three models differ in diameter. The FX-0009 measures 0.009mm, the FX-001 measures 0.01mm, and the FX-002 measures 0.02mm. Choose the thinnest option for the smallest pads and tightest traces.