Mechanic M60 0.4mm Solder Wire 40g Rosin Core
₨ 350
Fine-Gauge Rosin Core Solder for Mobile Boards
Mechanic M60 0.4mm solder wire gives your repair bench a precise, no-clean rosin core consumable in a 40g spool. The thin 0.4mm gauge lets you feed a small, controlled amount of tin-lead solder onto charging port pads, jumper points, and IC pads without bridging neighbouring contacts. You get steady flow from the rosin core, minimal residue after the joint cools, and enough wire per spool for repeated board-level jobs. Technicians doing fine-pitch hand soldering, pad tinning, and jumper work on mobile phone mainboards use this gauge as a daily-driver consumable next to a soldering station and a microscope.
In stock
Mechanic M60 0.4mm Solder Wire for Precision Mobile Board Soldering
Mechanic M60 0.4mm solder wire brings a fine-gauge, rosin-core consumable to your mobile repair bench. The 40g spool carries a no-clean flux core inside a tin-lead (Sn-Pb) alloy, so the wire melts, wets the pad, and flows without a separate flux step on most small joints. Technicians who work on charging port pads, jumper points, and shield-frame tacking choose this gauge because it feeds a small, controlled amount of solder at a time.
Why the 0.4mm Gauge Fits Mobile Board Repair
Thicker wire dumps too much solder on a pad and bridges neighbouring points. A 0.4mm wire lets you place a measured amount by touch, which matters near connectors, test points, and small ICs. When you do IC change karna jobs or tin the pads before placing a new component, the thin gauge keeps the pad profile flat and even. Pair it with a fine tip on your soldering station and a microscope, and you control every joint you make on a dense board.
Rosin Core and No-Clean Flux in Daily Workflow
The rosin core releases flux the moment the wire melts, so flux reaches the joint exactly when you need it. The no-clean formulation leaves minimal residue, which cuts the board-cleaning time between jobs on a busy repair day. You still wipe visible residue from sensitive areas such as connector contacts, but the joint itself stays tidy and bright without a heavy cleaning routine. For a workshop that handles dozens of boards a day, that saved time adds up across every charging issue and display problem job.
Where It Sits in Your Soldering Workflow
Mechanic M60 0.4mm solder wire works at the hand-soldering stage of the repair chain. Use it with a soldering station for jumper lagana on broken tracks, with a hot air station when you add solder to pads before reflowing a component, and with a reballing kit when you tin pads ahead of a reball. A PCB holder keeps the board steady while you feed the wire, and a multimeter confirms continuity after every jumper. These steps cover many dead phone cases caused by a broken charging line, and they support the hardware fault checks that come before you test a phone that hangs on logo.
Working With a Tin-Lead Alloy
The Sn-Pb alloy melts at a lower temperature than typical lead-free solder, so it flows quickly and forgives small variations in iron temperature. Lead-bearing solder asks for good habits: run a fume extractor or work in a ventilated space, and wash your hands before you eat. Keep the spool capped or wrapped between jobs so the wire stays clean and the rosin core stays intact on your bench.
| Weight | 0.40 kg |
|---|
Key Features
- ✓Fine 0.4mm diameter for controlled solder delivery
- ✓40g spool for repeated workshop use
- ✓Rosin core flux inside the wire
- ✓No-clean formulation with minimal residue
- ✓Sn-Pb tin-lead alloy that flows at a lower temperature than lead-free
- ✓Suits fine-pitch pads and tight areas on mobile boards
- ✓Works with soldering stations and hot air rework
- ✓Universal use across mobile and general electronics PCBs
Specifications
| Brand | Mechanic |
|---|---|
| Model | M60 |
| Category | Solder Wire / Soldering Consumables |
| Compatibility | Universal — general electronics and mobile PCB soldering, not device-specific |
| Technology | No-clean rosin core flux |
| Material | Sn-Pb (tin-lead) alloy |
| Wire Diameter | 0.4mm |
| Weight | 40g |
Common Repair Uses
- ✓Hand soldering and pad work during board-level mobile repair
- ✓Charging port pad soldering
- ✓Jumper wire lagana on broken tracks
- ✓IC pad tinning before IC change karna
- ✓Component tacking and re-soldering
- ✓Pad tinning ahead of reballing
- ✓Battery connector repair
- ✓Shield frame and small connector soldering
- ✓General PCB rework
Compatible Devices
- ✓Universal — works on any PCB or mainboard you solder by hand; not device-specific
- ✓Android smartphone mainboards (Samsung, Oppo, Vivo, Infinix, Tecno, Xiaomi, Realme)
- ✓iPhone logic boards
- ✓Charging port sub-boards
- ✓Display and flex connector pads
- ✓Small-signal ICs and passive component pads
- ✓Battery connector pads
- ✓Tablet mainboards
- ✓General electronics PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is Mechanic M60 solder wire lead-free?
Is 0.4mm solder wire good for jumper and IC pad work on mobile boards?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock



