Sunshine S2 Soldering Station with C210 Handle & Tip

₨ 10,500

Sunshine S2 C210 Digital Soldering Station

The Sunshine S2 soldering station gives your repair bench a digital-display control unit, a C210 handle, and an integrated C210-SK heating core. Rated heat-up takes about 1 second and tinning about 2 seconds. Three temperature memory channels, intelligent sleep, and temperature correction keep your settings consistent from one board to the next. The station accepts the universal C210 series tip range, so you can expand your tip library as your work demands. The 40W output suits phone mainboard joints, charging-port repairs, and shield-adjacent work where heat control decides the result. Mechanicpk supplies this set across Pakistan for technicians and service centers that want a compact, spec-led C210 platform.

In stock

12 People watching this product now!
Description

Sunshine S2 Soldering Station for Precision Mainboard Work

The Sunshine S2 soldering station packs a digital-display control unit, a C210 handle, and an integrated C210-SK heating core into one compact set. The C210 platform builds the heater and tip into a single replaceable cartridge, so heat reaches the joint with less lag than a conventional heater-and-tip pair. Mechanicpk supplies this configuration as a handle-and-single-tip set. It suits technicians who already stock spare C210 cartridges, and it gives new buyers a clean entry point into the platform. If you solder dense smartphone mainboards every day, the S2 delivers a stable 40W source sized for that work.

C210 Heating Core Performance

The integrated C210-SK heating core combines the heating element and the tip in one nano-plated unit. The manufacturer rates heat-up at about 1 second and tinning at about 2 seconds, so the iron reaches working temperature almost as soon as you lift it from the stand. The nano-plating resists oxidation and corrosion, which protects the tinned surface through long shifts at the bench. Because the cartridge is integrated, you swap the whole tip when it wears out instead of rebuilding a heater assembly. The tip-to-ground impedance stays below 2 ohms, which matters when you work near static-sensitive ICs and want the tip referenced properly to ground. The S2 also supports the universal C210 series tip range, so you can move between fine-point and broader tip styles as the joint requires.

Temperature Control and Memory Channels

The S2 uses a digital display, so you read the set temperature directly instead of estimating from a dial. The station covers a 90°C to 450°C range, which spans low-heat work on delicate flex connectors and higher-heat work on large ground-plane joints. Three memory channels store your preferred temperatures, so you recall a lead-free profile, a leaded profile, or a ground-plane profile with a button press rather than retuning each time. Temperature correction lets you adjust the displayed value against your own reference, and intelligent sleep lowers heat during idle periods to protect the tip and cut power use. A multifunction stand holds the handle and provides a cleaner, a high-temperature-resistant sponge, and a slot for swapping the heating core. You clean and re-tin without reaching for separate accessories.

Where It Fits in a Repair Workflow

You reach for the S2 at several stages of a mainboard repair. During diagnosis of a hardware fault, you reflow suspect joints and reseat small components. When a charging issue traces back to a damaged connector or a lifted pad, the fine C210 tip lets you rebuild the joint under magnification. On a dead phone that needs a jumper repair, you lay a bridge wire across a broken trace with controlled heat. During IC change karna jobs, you clean old solder from pads and tin them before the new part goes down. The station complements the rest of a bench: pair it with a hot air station for BGA removal, a microscope for pad inspection, a reballing kit for chip-level work, a PCB holder to steady the board, and a multimeter to confirm continuity after each repair. If your workflow includes ISP pinout tools or eMMC programmers, you also use the iron to tack fine wires onto test points.

Bench Setup and Power Requirements

The S2 accepts 110 to 220V AC at 50 to 60Hz, so it runs on standard Pakistani mains supply without an external converter. The control unit measures 142 x 94 x 50mm and weighs about 710g, which leaves room on a crowded bench and moves easily between workstations. The rated operating environment spans 0°C to 40°C. Inside the box you get the host unit, a power cord, a C210 handle, and one C210-SK heating core, so you can start soldering after unpacking. Service centers that run several benches can standardize on the S2 and share C210 cartridges across stations. That keeps your tip inventory simple and your technicians working with identical heat behavior from bench to bench.

Additional information
Weight1.3 kg
Q & A
Please login to post questions

Key Features

  • Integrated C210-SK heating core with nano-plated tip
  • Rated 1-second heat-up and 2-second tinning
  • Digital temperature display
  • 90°C to 450°C temperature range
  • Three temperature memory channels
  • Intelligent sleep and temperature correction
  • Multifunction stand with cleaner, sponge, and core swap slot
  • Wide 110–220V input for local mains supply

Specifications

BrandSunshine
ModelS2
CategorySoldering Station
CompatibilityC210 series soldering iron tips (integrated heating core design)
TechnologyDigital display, 3-channel temperature memory, intelligent sleep, temperature correction
Temperature Range90°C – 450°C (194°F – 842°F)
Input VoltageAC 110–220V, 50/60Hz
Power Rating40W (C210 handle)
Tip-to-Ground Impedance
Operating Environment0°C – 40°C (32°F – 104°F)
Dimensions142 x 94 x 50mm (host unit)

Common Repair Uses

  • Hand soldering, desoldering, and pad preparation on mobile and general electronics boards
  • Charging port solder joint repair
  • Jumper lagana on broken traces
  • Pad cleaning and tinning before IC change karna
  • Reflowing suspect joints during hardware fault diagnosis
  • Soldering fine wires to ISP and eMMC test points
  • Component replacement on small SMD parts
  • Large ground-plane and shield joint soldering
  • Cleaning residue after BGA removal

Compatible Devices

  • Universal — not device-specific; suits any mobile board that needs hand soldering
  • Android smartphone mainboards
  • iPhone logic boards
  • Tablet motherboards
  • Charging port and flex connector joints
  • Small SMD components and passives
  • Shield-adjacent power and ground sections
  • Jumper wire and test point connections
  • Laptop and general electronics PCBs

FAQ

What is the product name?
The product name is Sunshine S2 C210 Soldering Station with 1 Tip.
What is the brand of this product?
The brand of this product is Sunshine.
What is the model of this product?
The model of this product is S2.
What is this product used for?
This product is used for hand soldering, desoldering, and pad preparation on mobile phone mainboards and other electronics PCBs.
Which devices are compatible with this product?
This product is universal and not device-specific. It works with the C210 series soldering iron tips.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What temperature range does the Sunshine S2 soldering station cover?
The Sunshine S2 covers 90°C to 450°C and stores three temperature settings in its memory channels.
Can the Sunshine S2 use other C210 series tips?
Yes. The S2 supports the universal C210 series tips, and the included C210-SK heating core is one option from that range.