GSM-Sources 861 Series 8mm Hot Air Nozzle

₨ 1,200

8mm Nozzle for 861 Series Stations

The GSM-Sources 8mm hot air nozzle for 861 series stations narrows your hot air stream into a focused outlet for mid-size components. You fit it onto your 861 series hot air handle and aim heat at the IC, connector or shield can you need to lift, while the surrounding parts stay cooler. The 8mm opening suits board-level jobs on charging, display and power sections, from IC change karna to shield removal. Keep it on your bench as a dedicated size or as a spare next to your other 861 nozzles. Mechanicpk supplies it for technicians and repair shops across Pakistan.

In stock

11 People watching this product now!
Description

8mm Hot Air Nozzle for 861 Series Rework Stations

The GSM-Sources 8mm hot air nozzle for 861 series stations gives your hot air gun a mid-size outlet that concentrates airflow on one component instead of the surrounding board area. You fit it onto the 861 series handle, set your temperature and airflow, and direct heat exactly where the repair needs it. At 8mm, the opening sits between small passive work and large chip work, so it earns a permanent slot in a technician’s nozzle rack. Mechanicpk stocks it for repair shops that run 861 series stations every day and want a dependable size on hand.

How a Focused Outlet Protects the Board

A bare hot air gun outlet spreads heat across a wide patch. That heat reaches flex connectors, plastic sockets, nearby capacitors and glued shields you never meant to touch. A nozzle narrows the stream, so the heat lands on the target area and the neighbouring parts take less of it. You still control temperature and airflow at the station, so start low, add heat in steps and watch the solder flow. Pair the nozzle with a PCB holder to keep the board steady and a microscope to watch the solder melt. That combination gives you clean lifts and fewer collateral hardware faults.

Where the 8mm Size Fits Your Repair Workflow

Mid-size nozzles do the bulk of everyday rework, and the 8mm size covers a wide share of that range. You can use it to remove and refit charging ICs, power management ICs, audio ICs and other mid-size packages during a charging issue or dead phone repair. It also works for lifting small shield cans and warming connectors when you chase a display problem or a hang on logo fault that traces back to a joint. After the lift, you clean the pads, apply fresh flux and reflow the new part. Reballing kits and stencils handle the next stage for BGA parts. Multimeters confirm continuity and shorts once the board cools. Choose a smaller nozzle for tight spots and a larger one for wide shields, and treat the 8mm as your balanced middle size.

Fitting and Using the Nozzle on 861 Series Stations

This nozzle targets 861 series hot air stations, so check that the outlet on your handle matches before you buy. Slide the nozzle on, seat it fully and tighten any retaining screw just enough to hold it, since forcing it can deform the fit. Let the handle cool before you swap nozzles. Keep the stream moving in small circles above the part rather than parking it on one spot, and stop heating as soon as the solder flows. If you work under a microscope, check the nozzle angle on your station setup, because a straight outlet and an angled outlet change how well you see the joint.

If you upgrade from basic soldering irons to a full hot air workflow, this nozzle adds control without adding a new station. Stock several sizes from the Hot Air Stations and Soldering Stations categories so each job gets the right outlet.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 8mm outlet size for mid-size component rework
  • Built for 861 series hot air stations
  • Concentrates airflow on the target component
  • Helps protect neighbouring connectors and capacitors from stray heat
  • Suits charging, power and audio IC work
  • Works with preheating and flux-based rework routines
  • Useful as a main size or a spare in your nozzle set
  • Fits a workflow built around PCB holders and microscopes

Specifications

BrandGSM-Sources
ModelNozzle 861 Series 8mm
CategoryHot Air Gun Nozzle
Compatibility861 series hot air stations
Nozzle Size8mm

Common Repair Uses

  • Hot air rework on mobile phone boards where a focused 8mm airflow outlet helps.
  • IC change karna on mid-size chips
  • Charging IC removal and refit for a charging issue
  • Power IC replacement on a dead phone
  • Shield can lifting
  • Connector warming and reflow
  • Display problem joint repair
  • Hang on logo hardware fault diagnosis
  • Pad cleaning and board prep after component removal

Compatible Devices

  • Universal — not phone-model-specific. Fits 861 series hot air stations and works on boards from any phone brand that needs mid-size hot air rework.
  • 861 series hot air rework stations
  • Android smartphone motherboards
  • iPhone motherboards
  • Tablet motherboards
  • Mid-size charging and power ICs
  • Audio and other mid-size IC packages
  • Small shield cans
  • Board-mounted connectors

FAQ

What is the product name?
The product name is GSM-Sources Nozzle 861 Series 8mm.
What is the brand of this product?
The brand of this product is GSM-Sources.
What is the model of this product?
The model of this product is Nozzle 861 Series 8mm.
What is this product used for?
This product is used for directing hot air onto mid-size components during mobile phone board rework.
Which devices are compatible with this product?
This product is compatible with 861 series hot air stations and works on boards from any phone brand.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which hot air stations does the 8mm 861 series nozzle fit?
It targets 861 series hot air stations. Check that the outlet on your handle matches the nozzle before you buy.
Is an 8mm hot air nozzle right for IC change on a dead phone board?
Yes for mid-size ICs such as charging and power ICs. Use a smaller nozzle for tiny parts and a larger one for wide shields or big BGA chips.