Magma C115 Soldering Iron Tip (Curved) – Precision SMD Tip

₨ 2,200

Precision Curved C115 Tip for SMD Rework

The Magma C115 Soldering Iron Tip (Curved) gives you a bent, precision tip built on the C115 cartridge system, where the heating element and temperature sensor sit inside one unit. The curved geometry opens up your line of sight to the pad, so you place heat exactly where a small SMD component, connector pin, or jumper point needs it. Technicians use it on phone motherboards where shields, flex connectors, and tightly packed parts limit access. The tip measures approximately 11 mm in length and fits C115 / T115 compatible handles and stations. Each pack contains one tip. Pair it with a hot air station and a microscope for clean board-level work.

In stock

18 People watching this product now!
Description

Magma C115 Soldering Iron Tip for Precision Mobile Board Rework

The Magma C115 Soldering Iron Tip (Curved) is a bent-profile tip for the C115 cartridge standard, built for technicians who work at component level on phone motherboards. A C115 cartridge packs the heating element and the temperature sensor into the same body as the tip, so heat reaches the joint quickly and the station reads the temperature right at the work point. The curve moves the iron body out of your sightline, which matters when you rework small passives, fine connector pins, or test-point wires under a microscope. Mechanicpk stocks this tip for Pakistani repair shops, service centers, and training labs that need a dependable consumable for daily SMD work.

Why a Curved Soldering Tip for Mobile Repair Matters

A straight tip forces you to tilt your wrist and block your own view of the pad. The curved profile fixes that problem. You hold the handle at a comfortable angle, and the bent end reaches the joint from the side, so you watch the solder flow and the pad edge while you work. Crowded boards benefit most, because shield cans, flex connector housings, and neighboring ICs leave very little room around the target pad. The shape targets SMD components and limited-access areas, which describes most of a modern phone board.

You can use this C115 curved soldering tip on charging port pins, battery connector pads, small capacitors and resistors, and jumper points beside larger ICs. The tip length of approximately 11 mm keeps the working end compact, so you position it with control instead of fighting the handle. Steady control matters when a charging issue or display problem traces back to one lifted pad, because a single careless touch can lift the next one.

C115 Cartridge Design: Heater and Sensor in One Unit

The tip belongs to the C115 standard, which combines the heater and the sensor in one cartridge. That integrated layout supports rapid heat-up and a stable working temperature, so you finish a joint fast and keep heat exposure short. Short exposure protects delicate pads and small components on thin phone boards, where extra seconds under the iron can turn a simple fix into a damaged track.

Check your handle or station before you order. This tip fits C115 / T115 compatible handles and stations, so confirm that your hardware accepts the C115 cartridge format. The tip itself stays universal across phone brands, because it works on the solder joint and does not depend on a specific phone model. Your Samsung, Oppo, Vivo, Infinix, Tecno, and iPhone repairs all call for the same precise heat delivery, so one tip serves a mixed bench workload.

Where It Fits in Your Mobile Repair Workflow

On a dead phone, you usually start with a Multimeter check on the power rails, then replace the failing part. This tip handles the soldering side of that job: replacing a damaged charging port pin, resoldering a battery connector, or laying a jumper wire across a broken track. When a board needs ISP work after a dead after flash fault, you solder fine wires to the test points, and the curved end reaches those pads without touching their neighbors. Hold the board in a PCB Holder so both hands stay free, and add a Microscope for magnification on every fine-pitch joint.

The tip works best as one part of a complete bench. Use a Hot Air Station to lift shields and BGA parts, and keep Reballing Kits within reach when a CPU or eMMC needs fresh solder balls. Your ISP Pinout Tools, eMMC Programmers, and UFS Adapters handle the data side of the repair, and Test Boxes let you confirm the phone boots after you finish soldering. If your current iron limits your precision, move up to a dedicated Soldering Station that accepts C115 cartridges, so your bench gets stable temperature control along with this tip.

Additional information
Weight0.5 kg
Q & A
Please login to post questions

Key Features

  • Curved tip shape improves solder point visibility on crowded boards
  • C115 cartridge design with heating element and temperature sensor in one unit
  • Rapid heating and stable working temperature for short heat exposure
  • Approximately 11 mm tip length for compact, controlled positioning
  • Fits C115 / T115 compatible handles and stations
  • Suited to precision SMD soldering and small component work
  • Reaches pads in limited-access areas of phone motherboards
  • Supplied as a single tip

Specifications

BrandMagma
ModelC115-IS (Curved)
CategorySoldering Iron Tips
CompatibilityC115 / T115 compatible handles and stations
TechnologyC115 cartridge system with integrated heating element and temperature sensor
DimensionsTip length approx. 11 mm

Common Repair Uses

  • Precision soldering and rework on phone motherboards where access is limited.
  • SMD component replacement
  • Charging port pin soldering
  • Battery connector resoldering
  • Jumper wire soldering on broken tracks
  • Fine wire soldering to ISP and test points
  • Soldering beside shields and flex connectors
  • Motherboard repair for charging issue and display problem faults
  • Small component rework under a microscope

Compatible Devices

  • Universal soldering tip, not phone-model specific. It fits C115 / T115 compatible handles and stations and works on boards from any phone brand.
  • C115 / T115 compatible soldering handles
  • C115 / T115 compatible soldering stations
  • Samsung phone motherboards
  • Oppo and Vivo phone motherboards
  • Infinix and Tecno phone motherboards
  • iPhone logic boards
  • Other Android and smartphone PCBs
  • Small SMD and flex-connector areas with limited access

FAQ

What is the product name?
The product name is Magma C115 Soldering Iron Tip (Curved).
What is the brand of this product?
The brand of this product is Magma.
What is the model of this product?
The model of this product is C115-IS (Curved).
What is this product used for?
This product is used for precision SMD soldering and rework on phone motherboards, especially in tight areas where a straight tip blocks your view.
Which devices are compatible with this product?
This product fits C115 / T115 compatible handles and stations. The tip is universal and works on boards from any phone brand.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which handles and stations fit the Magma C115 curved tip?
The tip fits C115 / T115 compatible handles and stations. Confirm that your handle accepts the C115 cartridge format before you order.
Does this tip include its own heater and sensor?
Yes. The C115 cartridge system builds the heating element and the temperature sensor into the tip, so you do not buy a separate heater.