Magma C115 Blade Soldering Iron Tip
₨ 1
Magma C115 Blade Tip for Precision Soldering
The Magma C115 blade soldering tip gives your C115-series handle a flat, wide contact edge for drag soldering, pad tinning and connector rework. You run it on a matching C115 soldering station handle and use it for charging port repair, battery connector joints, FPC pads and board cleanup on mobile motherboards. The plated stainless steel housing limits heat loss and tin climbing, so your tip stays cleaner between joints. Mechanicpk supplies this tip to repair shops, service centers and technicians across Pakistan who need a reliable C115 consumable at the bench every day.
Out of stock
Magma C115 Blade Soldering Tip for Fine Board-Level Repair
The Magma C115 blade soldering tip puts a flat, wide contact edge on your C115-series handle, so heat moves into a pad, shield or connector joint faster than a needle-point conical tip allows. Technicians working on dead phone boards know the problem: a fine conical tip tins a single pad well but crawls through a row of connector pins. The blade profile clears that row in one pass. Mechanicpk stocks this tip for workshops across Pakistan that want a dependable soldering consumable for daily station use, from charging port repair to board-level rework on Samsung, Oppo, Vivo, Infinix and Tecno boards.
How the Blade Profile Fits Your Repair Bench
A blade tip spreads heat along a straight edge instead of a single point. You drag it across a row of pins and the solder follows the edge, which suits charging ports, battery connectors, FPC connectors and SIM tray pads. You also use the flat face to tin a pad before an IC change karna job and to clean bridged pins after a reflow. When a hardware fault such as a charging issue or display problem traces back to a damaged connector, the blade lets you lift and re-solder the joint without wandering onto neighbouring components. Keep the tip tinned between joints and wipe it on brass wool rather than a wet sponge, because repeated thermal shock shortens the life of any plated tip.
C115 Series Matching: Tip and Handle Must Agree
C115 names a tip series, so your handle and tip must belong to the same series. A C115 handle takes C115 tips only, and a C210 or C245 handle will not accept this one. Magma lists its C115 range as lead-free heating core tips with a stainless steel housing that reduces heat loss, a plating layer that resists tin climbing and a nickel coating against rust and corrosion. Check the label on your soldering station handle before you order. If it reads C115, this tip fits. You can build out the rest of your bench with Soldering Stations and Hot Air Stations from the Mechanicpk range, and add a Microscope for the fine pad work that the C115 series targets.
Where the Magma C115 Blade Soldering Tip Sits in Your Workflow
Soldering rarely stands alone in a repair. A typical dead after flash job starts with a Multimeter reading on the charging line, moves to a Test Box or ISP Pinout Tools check, and ends with a joint you must re-solder. On ISP work you solder fine wires to test points, then remove them and clean the pads, and the blade edge clears leftover solder from those pads quickly. Reballing Kits and PCB Holders belong in the same workflow, because a held, stable board lets the tip do its job. eMMC Programmers and UFS Adapters depend on clean pads and solid joints, so a fresh, well-tinned tip protects the work you finish before the programmer ever reads the chip. If your current tip no longer wets properly or climbs tin up the barrel, replace it before the next board, not after the next failed joint.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Blade profile with a flat, wide contact edge
- ✓C115-series tip for matching C115 handles
- ✓Lead-free heating core design
- ✓Stainless steel housing to reduce heat loss
- ✓Plating layer to reduce tin climbing
- ✓Nickel coating against rust and corrosion
- ✓Iron plating layer for durability
- ✓Replaceable tip, so you swap the tip instead of the whole handle
Specifications
| Brand | Magma |
|---|---|
| Model | C115 (Blade) |
| Category | Soldering Iron Tips |
| Compatibility | C115-series soldering handles (handle and tip must be the same series) |
| Technology | Soldering tip with integrated lead-free heating core |
| Material | Stainless steel housing with iron plating layer and nickel coating |
Common Repair Uses
- ✓Fine soldering and rework on mobile phone boards where a flat contact edge helps.
- ✓Charging port solder joint repair
- ✓Battery and FPC connector re-soldering
- ✓Pad tinning before IC change
- ✓Drag soldering across connector pin rows
- ✓Cleaning bridged pins after reflow
- ✓Clearing solder from pads after ISP wire removal
- ✓Jumper lagana on broken tracks
- ✓General board cleanup during hardware fault diagnosis
Compatible Devices
- ✓Universal soldering tip, not phone-model-specific. It works on any mobile board a C115-series handle can service.
- ✓C115-series soldering station handles
- ✓Samsung mobile boards (general soldering and connector rework)
- ✓Oppo mobile boards (general soldering and connector rework)
- ✓Vivo mobile boards (general soldering and connector rework)
- ✓Infinix and Tecno mobile boards (general soldering and connector rework)
- ✓iPhone logic boards (connector and pad work)



