Magma C210 Soldering Iron Tip (Straight) for T210
₨ 1,500
Straight C210 Tip for Fine Soldering
The Magma C210 Soldering Iron Tip (Straight) gives you a slim, precise contact point for small pads, single pins and SMD joints. It follows the C210 cartridge standard with an integrated heating element, so the heater and tip work as one unit. The tip fits stations and handles that support the C210 / T210 system. Use it as your C210 soldering tip for mobile repair on charging ports, connectors, jumper work and fine motherboard touch-ups. Mechanicpk supplies it to repair shops and technicians across Pakistan who need dependable fine-pitch soldering consumables at the bench.
In stock
Magma C210 Soldering Iron Tip (Straight) for Precision Board Work
The Magma C210 Soldering Iron Tip (Straight) is a C210 soldering tip for mobile repair that puts a slim, straight contact point on the exact pad or pin you need to reach. Mechanicpk stocks it for technicians who work on dense smartphone boards, where a wide tip bridges neighbouring pads and a blunt tip never reaches the joint. The tip belongs to the Magma 210 series and follows the C210 cartridge standard, so the heating element sits inside the tip itself. When the tip wears out, you replace one part, and the heater, tip and contact surface renew together.
Precision Control on Small Pads and SMD Pins
The slim straight profile lets you work on single pins, small pads and SMD component legs without touching the parts around them. When you hold the iron at a natural angle over a charging connector or a flex socket, the tip lands on the target joint and stays there while you feed solder. That control matters on a dead phone with a lifted pad, where one careless touch tears the trace. You also keep a clear line of sight under the microscope, because the slim tip does not block the joint you are watching. Pair it with a microscope and a PCB holder that locks the board flat, and your hand steadies on the joint instead of fighting the fixture. For jumper lagana on a broken track, the fine contact point lets you tin the pad, place the wire and reflow in one clean pass. This straight soldering tip for SMD work suits technicians who prefer light, deliberate contact over heavy pressure.
C210 Cartridge Design and Handle Fit
Magma builds this tip to the C210 standard, which integrates the heating element into the tip. That layout shortens the path between the heat source and the solder, so you get fast heat-up and steady temperature at the joint. The tip fits stations and handles that support the C210 / T210 system, so check your station’s handle type before you order. If your bench runs a C210-compatible soldering station, the tip seats directly in the handle with no adapter. Keep a spare in your drawer, because a tip that fails mid-repair stalls the whole job and leaves the customer’s phone on your bench overnight. Good habits stretch tip life: tin the tip before you park the iron, wipe it on brass wool or a damp sponge, and set your temperature only as high as the joint demands.
Where It Fits in a Mobile Repair Workflow
A typical board-level job starts with diagnosis. You read the board with a multimeter or a test box, trace the hardware fault, then decide whether the repair needs hot air rework or fine pin soldering. The Magma C210 straight tip covers the second path. You resolder a charging port pin, touch up a connector joint, attach a jumper wire after a lifted trace, or clean a pad before a reballing kit goes to work on a nearby BGA. Charging issue, display problem and network issue repairs all finish with a handful of small joints, and this tip handles them without a larger iron crowding the board. Workshops that run several benches gain from standardising on one tip type, because every technician reaches for the same consumable and nobody hunts for a mismatch mid-repair. Add it to your order alongside your hot air station, reballing kits and PCB holders, and your bench stays ready for both rework and precision soldering.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Slim straight tip for small pads, single pins and SMD pins
- ✓C210 cartridge standard with integrated heating element
- ✓Heater and tip replace together as one part
- ✓Fast heat-up and stable temperature at the joint
- ✓Fits stations and handles supporting the C210 / T210 system
- ✓Clear line of sight under a microscope
- ✓Suits motherboard repair, GSM service and precision electronics
- ✓Supplied with a protective box or tube
Specifications
| Brand | Magma |
|---|---|
| Model | C210-I |
| Category | Soldering Iron Tips |
| Compatibility | Stations and handles supporting the C210 / T210 system |
| Technology | C210 cartridge-style tip with integrated heating element, straight tip shape |
Common Repair Uses
- ✓Fine-pitch soldering tasks on mobile and consumer electronics boards
- ✓Precision soldering of SMD components
- ✓Soldering single pins and small solder pads
- ✓Resoldering charging port pins
- ✓Touching up connector and socket joints
- ✓Attaching jumper wires to lifted pads and broken tracks
- ✓Cleaning and re-tinning pads before further rework
- ✓Motherboard repair on dead phone and charging issue faults
- ✓Microscope-assisted micro soldering
Compatible Devices
- ✓Universal soldering tip, not phone-model specific; compatibility depends on the C210 / T210 handle or station
- ✓Soldering stations that support the C210 / T210 system
- ✓Handles that accept C210 cartridges
- ✓T210-type precision soldering handles
- ✓Smartphone motherboards with small SMD pads and pins
- ✓Charging port and connector solder joints
- ✓Consumer electronics boards needing fine-pitch soldering
- ✓GSM service bench setups used for board-level repair
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which handles and stations accept the Magma C210 straight tip?
Does the Magma C210 tip have a separate heating element?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock



