2UUL DA18 BB Shark Blade No.11 (100Pcs/Box) for IC Glue
₨ 2,400
No.11 Blade for Mobile Repair Benches
The 2UUL DA18 BB Shark Blade No.11 (100Pcs/Box) gives repair benches a dependable No.11 blade for mobile repair work that involves residual glue on CPU and IC areas. Each high-carbon steel blade comes individually packed and rust-proof, with a tear-notched pack that lets you grab a fresh edge in seconds. The edge resists deformation, so you scrape glue off the motherboard without fighting a bent tip. A 100-piece box suits shops that clean boards every day. Mechanicpk supplies the DA18 to technicians and service centers across Pakistan who want a fresh blade for every job.
In stock
No.11 Blade for Mobile Repair: 2UUL DA18 BB Shark Overview
The 2UUL DA18 BB Shark Blade No.11 (100Pcs/Box) is a consumable cutting blade for technicians who need a sharp, reliable No.11 blade for mobile repair at board level. Glue on a phone motherboard hides solder pads, bridges neighboring components, and blocks clean heat transfer to the joints you want to rework. This blade removes that residue from CPU and IC areas, so you start every reballing or chip replacement job on a clean surface. The 100-piece box matches how repair shops actually work: you change blades often, and you never want to scrape glue with a dull edge.
Key Technical Highlights
2UUL builds the DA18 from high-carbon steel and designs the edge to resist deformation. That matters when you push a pointed tip along a fine pad row. A bent or rolled edge drags across the board and risks lifting a pad, so a rigid blade gives you more control on boards that already carry weak traces. The No.11 pattern gives you a sharp point and an edge ground along one side, which reaches into the narrow gaps around a CPU or IC where a wider blade cannot fit.
Packaging protects the edge before you ever touch it. Each blade sits in its own rust-proof pack, and a tear notch lets you open the pack with one hand while your other hand holds the board. You pull out a clean, sharp blade for each repair, which keeps your glue-cleaning results consistent from the first board of the day to the last. A sealed single-blade pack also keeps loose blades out of your tool drawer and away from your fingers.
Mobile IC Glue Removal Blade in Your Repair Workflow
Use the DA18 as your mobile IC glue removal blade in the cleaning stage of board-level repair. After you warm the area with a hot air station and soften the glue, you scrape residue away from the edges of the CPU or IC. Once the chip is off, you clear the leftover glue from the pads before you reball or reflow a replacement. The goal stays the same in every case: expose clean copper without scratching the board or the chip. Hold the blade at a low angle against the board and push away from the pad row rather than across it. That angle lifts glue in strips, keeps the tip off the copper, and gives you a visible cut line to follow under magnification. Keep a second blade ready for stubborn residue, since a fresh edge on the final pass leaves the cleanest pad surface.
Pair the blade with a microscope so you see exactly where glue ends and the pad begins. Clamp the board in a PCB holder so your hand stays steady, and keep flux and tweezers close, since the same bench usually covers cleaning, soldering, and final testing. Work with light pressure and short strokes, and let the sharp edge do the cutting. Swap the blade as soon as the tip loses its bite, because a fresh blade costs far less than a damaged pad. Check the cleaned board with a multimeter before you move on to soldering.
Why Repair Shops Stock the 100-Piece Box
Repair shops that handle dead phone, charging issue, and display problem boards every day burn through blades quickly. A 100-piece box lowers your cost per blade and keeps a fresh edge ready for every job, instead of pushing you to reuse a worn one. Service centers and training institutes benefit too, since trainees go through blades while they learn glue-cleaning technique.
2UUL also lists the DA28 FlatCut blade, a separate flat-edge blade sold in 5-piece boxes for solder pad underfill glue removal. The DA18 No.11 covers the pointed-tip side of the job, so you can keep both styles on your bench. Mechanicpk stocks the DA18 alongside hot air stations, soldering stations, reballing kits, PCB holders, and microscopes, so you can set up a complete glue-cleaning and reballing bench from one supplier in Pakistan.
| Weight | 0.9 kg |
|---|
Key Features
- ✓High edge deformation resistance
- ✓High-carbon steel construction
- ✓Individually packaged blades
- ✓Rust-proof packaging
- ✓Tear-notched pack for quick one-hand opening
- ✓100-piece box for daily workshop use
- ✓No.11 pointed profile for tight areas around CPU and IC chips
- ✓Designed to remove residual glue without damaging the motherboard or CPU chip
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA18 BB Shark Blade No.11 (100Pcs/Box) |
| Category | Mobile Repair Blades and Scrapers |
| Compatibility | Mobile phone PCB, CPU and IC glue cleaning (universal, not device-specific) |
| Supported Devices | Universal, not device-specific |
| Material | High-carbon steel |
Common Repair Uses
- ✓Glue cleaning at CPU and IC level on mobile phone boards.
- ✓Cleaning residual glue around CPU chips
- ✓Scraping glue from IC edges before chip removal
- ✓Clearing leftover glue from pads after chip removal
- ✓Cleaning glue residue from phone motherboards
- ✓Preparing pad areas for reballing or reflow
Compatible Devices
- ✓Universal scope. The blade is not device-specific and works wherever glue needs cleaning on a mobile phone PCB.
- ✓Mobile phone motherboards (universal, not brand-specific)
- ✓CPU glue areas on mobile phone PCBs
- ✓IC glue areas on mobile phone PCBs
- ✓BGA chip edges with residual glue
- ✓Board surfaces around solder pads
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the 2UUL DA18 No.11 blade clean glue around a CPU without damaging the board?
What is the difference between the 2UUL DA18 No.11 blade and the DA28 FlatCut blade?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



