2UUL DW15 Solder Vampire Desoldering Wick 2015 10Rolls/BOX
₨ 2,500
Desoldering Wick for Mobile Repair Pakistan
The 2UUL DW15 Solder Vampire Desoldering Wick 2015 10Rolls/BOX gives your bench ten rolls of high-purity braided copper wick, each 2.0 mm wide and 1.5 m long. The fine weave and strong heat conductivity pull solder off mobile PCB pads quickly, leave minimal residue and keep thermal damage risk low. The copper resists oxidation and corrosion, works without extra flux in most cases and bends into tight spaces around ICs and connectors. Technicians use it to clean BGA pads, clear solder bridges and prepare boards for reballing. Mechanicpk supplies the full box for repair shops and service centers across Pakistan.
In stock
Desoldering Wick for Mobile Repair Pakistan: 2UUL DW15 Overview
Looking for a desoldering wick for mobile repair Pakistan workshops can buy by the box? The 2UUL DW15 Solder Vampire Desoldering Wick 2015 10Rolls/BOX packs ten braided copper rolls into one carton, and every roll measures 2.0 mm wide by 1.5 m long. That width suits the pad sizes you clean on smartphone mainboards, charging port footprints and BGA lands, so a single consumable covers most of your solder removal. Mechanicpk supplies the box for service centers and repair shops that use wick every day.
How the DW15 Braid Removes Solder Without Cooking the Pad
The DW15 uses high-purity copper braid with a fine weave. When you press the braid onto a joint with your iron tip, the copper conducts heat into the solder quickly and draws the molten alloy up into the weave. Good heat conductivity shortens the time the tip sits on the pad, which lowers the risk of lifting a pad or damaging a nearby component. The refined formulation leaves minimal residue behind, so the pad surface stays clean and flat for the next step. Most jobs need no extra flux, because each roll works straight from the box. The copper also resists oxidation and corrosion, so a roll that sits on your bench for a few weeks still wets properly when you need it. Flexible braid reaches tight areas between shield cans, connectors and neighboring ICs. Treat this 2mm desoldering wick as your default size for general board cleanup, and keep your pressure light, because force damages pads faster than heat does.
Solder Wick for PCB Rework Inside Your Repair Workflow
Wick earns its place at the end of every component removal. After your hot air station lifts a CPU, eMMC, UFS chip or PMIC, the board keeps a bed of excess solder that blocks clean placement. Lay the DW15 across the pads, heat it with your soldering station and wipe the surface flat. Under a microscope you can confirm that no bridges remain, and a multimeter checks continuity before you move on to reballing kits or fresh IC placement. The same routine helps when you prepare ISP pinout test points on a dead phone, clear a solder bridge behind a charging port that causes a charging issue, or clean a board after a failed rework that left a hardware fault. Wick also handles through-hole leftovers on connectors, shield frames and battery pads. A PCB holder keeps the board steady while you drag the braid, which gives you even pressure and a smoother pad. On fine pitch footprints, work in short passes and trim the used section of braid after each pass, so every pull uses fresh copper.
Why Repair Shops Buy the DW15 in the 10-Roll Box
A busy bench goes through wick quickly, and a half-used roll slows you down when you chase a boot loop issue or a hang on logo fault that turned out to be a bad eMMC joint. The ten-roll box keeps spare rolls ready for every technician station, so nobody shares or stretches a worn braid. You get a consistent 2.0 mm width across the whole box, which keeps your results repeatable from one repair to the next. The box also suits training institutes, where students burn through braid while they learn pad cleaning, and resellers who want a predictable consumable to stock beside their tool lines. Pair the wick with soldering stations, hot air stations, reballing kits and microscopes from the Mechanicpk range. Add eMMC programmers, UFS adapters or test boxes when your workflow moves from hardware cleanup to flashing and diagnostics. That upgrade path keeps one supplier behind your whole repair bench, from consumables to programming tools.
| Weight | 0.5 kg |
|---|
Key Features
- ✓10 rolls per box for continuous bench supply
- ✓2.0 mm wide and 1.5 m long per roll
- ✓High-purity copper braid for efficient solder absorption
- ✓Fast solder removal with minimal residue
- ✓Resists oxidation and corrosion
- ✓Fine weave and good heat conductivity lower the risk of thermal damage
- ✓Ready to use without extra flux in most cases
- ✓Flexible braid reaches narrow areas on dense boards
Specifications
| Brand | 2UUL |
|---|---|
| Model | DW15 (2015) |
| Category | Desoldering Wick |
| Compatibility | Universal — not device-specific |
| Technology | Braided copper desoldering wick |
| Material | High-purity copper |
| Dimensions | Roll width 2.0 mm; roll length 1.5 m |
| Pack Quantity | 10 rolls per box |
Common Repair Uses
- ✓Removing excess solder after CPU, eMMC, UFS or PMIC removal
- ✓Cleaning BGA pads before reballing
- ✓Clearing solder bridges between fine pitch pads
- ✓Cleaning pads behind charging ports after a charging issue repair
- ✓Preparing ISP pinout test points on a dead phone
- ✓Flattening pads before placing a replacement IC
- ✓Removing solder from through-hole joints and shield frame pads
- ✓Cleaning boards after a failed rework with a hardware fault
Compatible Devices
- ✓Universal — not device-specific. The wick works on solder joints and pads of any PCB.
- ✓Smartphone mainboards (all brands)
- ✓iPhone logic boards
- ✓Tablet motherboards
- ✓Laptop motherboards
- ✓Charging port and flex connector pads
- ✓BGA CPU, eMMC and NAND pads
- ✓Sub-boards and small module PCBs
- ✓General electronics PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What size are the rolls in the 2UUL DW15 desoldering wick box?
Does the 2UUL DW15 desoldering wick need extra flux?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



