2UUL SC97 Disposable Desoldering Flux for Mobile Repair
₨ 1,400
SC97 Flux for FPC and Dock Work
The 2UUL SC97 Disposable Desoldering Flux is a desoldering flux for mobile repair, built for the connector jobs that eat most of a technician’s bench time. This 15ml pack uses an acid-free, halogen-free, no-clean formula with premium solder powder, so one application helps you lift a part and seat its replacement. The gel body stays where you place it, which keeps FPC connectors, dock connectors and fine BGA pads under control. Mechanicpk supplies it for repair shops across Pakistan that want a predictable consumable for daily board-level work.
In stock
2UUL SC97 Disposable Desoldering Flux for Mobile Repair Benches
The 2UUL SC97 Disposable Desoldering Flux is a desoldering flux for mobile repair that targets one job: lifting and reseating small connectors on phone logic boards without damaging the pads underneath. 2UUL supplies it as a 15ml disposable pack with an acid-free, halogen-free, no-clean formula and premium solder powder, so the same material supports both removal and reinstallation. Mechanicpk stocks it for technicians who handle FPC connectors, dock connectors and fine-pitch components every day and want a consumable they can finish and replace instead of nursing a half-dried jar for months.
What the Formula Does on the Board
Mobile boards leave no room for corrosive residue. Thin copper pads and tiny traces suffer when a harsh flux sits under a connector for months, so the acid-free, halogen-free chemistry matters here. The flux attacks oxidation on old solder joints and improves solder flow, which lets pins release cleanly once your hot air or iron reaches working temperature. It also helps stop the joint from oxidizing again while you rework. The gel consistency holds its position under the part, so it does not run into neighbouring components the way a thin liquid flux can.
Where It Fits in a Dock and FPC Repair Workflow
A typical charging issue starts with a multimeter check on the dock pins. Once you confirm the connector is the fault, clamp the board in a PCB holder, apply a small amount of SC97 under and around the connector, and heat it with your hot air station. The connector lifts without dragging pads. You clean the pads under your microscope, add fresh flux, and seat the new connector. The solder powder in the paste gives you material on stripped pads, so a worn pad does not force you into a longer repair. The same sequence works for FPC sockets and other small ports on the logic board.
Application Notes for Clean Results
Use less than you think you need. A thin layer across the pads does the work, and extra flux only spreads around the component. The no-clean formula leaves minimal residue, so many repairs need no post-repair wash. If you want a spotless board for inspection or for a customer who watches your work, wipe the area with isopropyl alcohol after the joint cools. Keep the cap closed between jobs so the gel keeps its consistency on a busy workshop shelf.
Why Shops Stock It as a Consumable
The SC97 is a high-turnover item. A shop that replaces dock connectors and FPC sockets every day goes through flux steadily, and a disposable 15ml pack keeps each batch fresh and easy to count. It pairs with the rest of your soldering consumables and with tools from the Soldering Stations, Hot Air Stations and Reballing Kits categories. For BGA and micro-soldering work, the gel body gives you the control that fine pads demand. If your bench still relies on a generic flux for connector jobs, switching to a flux made for FPC and dock repair tightens your process without changing your equipment.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Acid-free, halogen-free formula for use on delicate phone boards
- ✓No-clean, low-residue finish that skips post-repair washing in many jobs
- ✓Removes oxidation and improves solder flow on old joints
- ✓Helps prevent re-oxidation during rework
- ✓Gel consistency that stays in place under connectors
- ✓Premium solder powder supports both removal and installation
- ✓Built for FPC connector and dock connector repair
- ✓15ml disposable pack for easy stock counting
Specifications
| Brand Entity | 2UUL |
|---|---|
| Product Entity | 2UUL SC97 Disposable Desoldering Flux 15ml |
| Technology Entity | Acid-free, halogen-free, no-clean flux with solder powder |
| Compatible Device Entities | Phone FPC connectors, dock connectors, mobile phone logic boards |
| Repair Process Entity | Connector desoldering, micro-soldering, BGA rework |
| Industry Entity | Mobile phone repair, PCB repair, soldering and rework consumables |
Common Repair Uses
- ✓Dock connector removal and replacement for charging issue repairs
- ✓FPC connector replacement
- ✓Removing and reinstalling small ports and sockets
- ✓BGA rework and reballing support
- ✓Micro-soldering on phone logic boards
- ✓Clearing oxidation from old solder joints before reflow
- ✓Reseating components on stripped pads using the solder powder in the paste
- ✓General board-level SMD rework
Compatible Devices
- ✓Any phone brand’s logic board (universal, not device-specific)
- ✓Phone FPC connectors
- ✓Phone dock (charging port) connectors
- ✓Small ports and sockets on phone motherboards
- ✓Small SMD components on phone PCBs
- ✓BGA components during micro-soldering and rework
- ✓Fine-pitch micro-soldering pads
- ✓Solder pads that need oxidation cleared before reflow
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is 2UUL SC97 flux acid-free and no-clean?
Can I use 2UUL SC97 flux for dock connector, FPC and BGA work?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



