YCS Number One Flux 10cc – No-Clean Repair Flux
₨ 750
No-Clean Flux for Mobile Repair Pakistan
YCS Number One Flux 10cc gives your repair bench a halogen-free, no-clean flux for CPU, NAND, PMIC and baseband soldering. It removes oxides from pads, blocks re-oxidation under heat and improves solder wetting during reballing, soldering and desoldering. The residue stays minimal and non-conductive, so you spend less time cleaning boards after each job. Pair it with a hot air station and a soldering station for motherboard-level work on phones, tablets and computer boards. The 10cc size keeps one dependable flux within reach for daily BGA and SMD rework.
In stock
YCS Number One Flux 10cc: No-Clean Flux for Mobile Repair Pakistan
YCS Number One Flux 10cc is a no-clean flux for mobile repair Pakistan workshops that run board-level jobs every day. The formula targets the soldering steps where heat control and wetting decide the result: CPU, NAND, PMIC and baseband IC work on phone and tablet motherboards. A halogen-free chemistry and a non-conductive residue keep the board clean enough to test as soon as the joint cools. The 10cc volume suits shops that reball and rework daily and want one consistent flux on the bench instead of switching products between jobs.
Chemistry and Technical Behavior
This flux handles three tasks. It removes oxides from pad and ball surfaces so molten solder bonds to bare metal. It forms a protective layer that blocks re-oxidation while the board sits under hot air or iron heat. It also improves wetting and heat transfer, which gives you smoother ball formation during reballing and cleaner joints during SMD placement. The no-clean classification means the leftover residue stays minimal and non-conductive, so it does not create leakage paths or short circuits on fine-pitch footprints. The halogen-free formula matters most when residue stays trapped under shields and BGA packages, where cleaning access is limited.
Where It Fits in Your Repair Workflow
Flux enters the workflow at every stage that melts solder. Before you lift a CPU or NAND chip, a thin flux layer around the package edge helps heat spread evenly across the solder balls. After removal, you coat the pads with fresh flux, clear the old solder with wick and iron, and inspect the pads under a microscope. Reballing comes next, and flux promotes uniform ball formation as the solder collapses under hot air. When you seat the IC back on the board, flux helps each ball wet its pad.
The same flux supports a PMIC change after a charging issue, baseband IC rework after a network issue, and small SMD component replacements once you confirm a hardware fault. Match it with your hot air station, soldering station, reballing kit and PCB holder so the heat profile and the chemistry work together. A multimeter check on the rebuilt section confirms the joints before you power the board.
Why Technicians Choose It for Daily Bench Work
Consistency drives buying decisions in a repair shop. A flux that behaves the same way on a dead phone, a boot loop issue after a failed flash or a hang on logo case lets you focus on the fault, not the consumable. Because the residue stays non-conductive, you can power the board and test right after the joint cools, which shortens the loop between rework and verification.
eMMC and UFS jobs often run an ISP pinout tool or an eMMC programmer beside the hot air station. A no-clean flux keeps the pad area tidy around those probe contacts, so your connections stay reliable. Distributor documentation lists the flux for mobile phone, tablet and computer board repair, which means one product covers most of what comes across a service center counter.
Stock YCS Number One Flux 10cc from Mechanicpk alongside your microscopes, reballing stencils, test boxes and hot air stations to build a complete motherboard repair bench.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Halogen-free no-clean formula
- ✓Removes oxides from metal surfaces before soldering
- ✓Blocks re-oxidation during heating
- ✓Improves solder wetting and heat transfer
- ✓Leaves minimal, non-conductive residue
- ✓Supports soldering, desoldering and BGA reballing
- ✓Suits CPU, NAND, PMIC and baseband IC work
- ✓10cc volume for daily workshop use
Specifications
| Brand | YCS |
|---|---|
| Model | Number One (No.1) Flux 10cc |
| Category | Soldering Flux |
| Compatibility | Universal — not device-specific |
| Supported Devices | Mobile phone, tablet and computer boards |
| Technology | No-clean, halogen-free flux |
Common Repair Uses
- ✓Flux-assisted soldering, desoldering and reballing at board level
- ✓BGA reballing of CPU, NAND and eMMC chips
- ✓CPU removal and reflow on motherboards
- ✓PMIC replacement for charging issue repairs
- ✓Baseband IC rework for network issue repairs
- ✓SMD component soldering after hardware fault diagnosis
- ✓Desoldering with hot air and soldering iron
- ✓Pad preparation and cleanup before IC placement
- ✓General PCB repair and maintenance
Compatible Devices
- ✓Universal flux — not tied to specific phone models; applies to boards and ICs that need flux-assisted soldering
- ✓Mobile phone motherboards
- ✓Tablet logic boards
- ✓Computer boards
- ✓CPU chips on BGA footprints
- ✓NAND and eMMC chips on BGA footprints
- ✓PMIC and charging ICs
- ✓Baseband ICs
- ✓SMD components on general electronics PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use YCS Number One Flux 10cc for CPU, NAND and PMIC reballing?
Do I need to clean the board after using this no-clean flux?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



