2uul BH31 The Smile JIG Fixture – PCB Holder
₨ 4,500
Universal PCB Holder for Board-Level Rework
The 2uul BH31 The Smile JIG Fixture holds a phone motherboard or BGA chip firmly while you rework it. Its two-way V-slot clamp and anti-slip base keep the board from shifting under hot air, so your soldering iron lands exactly where you aim it. The heat-resistant, easy-clean body suits daily bench use, and the 135 x 63 x 17 mm footprint takes little room on a crowded repair bench. Use it as a universal PCB holder for reballing, chip replacement, and board-level fault finding on dead phone, charging issue, and display problem jobs. It needs no installation: place the board, clamp, and start work.
In stock
2uul BH31 The Smile JIG Fixture for Stable Board-Level Rework
Board-level rework fails the moment the motherboard moves. The 2uul BH31 The Smile JIG Fixture is a PCB holder fixture for mobile repair that locks a phone board or IC chip in a two-way V-slot clamp, so your hot air gun and soldering iron work on a motionless target. Repair benches in Pakistan handle a steady flow of dead phone, charging issue, and hang on logo jobs, and every one of them starts with getting the board secured. 2UUL designed the BH31 as a compact, universal holder instead of a model-specific mount, so a single unit covers the boards you meet across a normal workday. Stability matters more than speed here. A board that drifts a millimetre under preheat can smear solder bridges across fine-pitch pads, and that turns a ten-minute IC change into an hour of cleanup.
How the V-Slot Two-Way Clamp Holds a Phone Board
The BH31 uses a two-way clamping design built around a V-slot. You seat the board edge or the IC body in the slot, close the clamp, and the V geometry positions the part quickly and accurately. An anti-slip surface adds friction at the contact points, which matters when a stream of hot air pushes against a bare PCB. Quick clamping also helps when you swap between boards during a busy shift. You spend seconds fixing a board instead of fighting with tape or improvised holders, and you keep both hands free for tweezers, flux, and the iron. The body resists high temperature and cleans easily, so flux residue and solder spatter wipe off after the job.
PCB Holder Fixture for Mobile Repair in Your Rework Workflow
Most board-level jobs follow one sequence. You diagnose with a multimeter or a test box, confirm the faulty section, then move the board to the rework stage. The BH31 sits at that stage. Clamp the board, bring in your hot air station or soldering station, and lift or replace the suspect IC. A charging issue often leads to the charging IC and its neighbouring components, and a display problem can lead to the display driver area. Both repairs demand a board that stays put through preheat and reflow. The fixture also supports reballing: hold the chip steady while you work with your reballing kit, then reflow it back into place. Pair the jig with a microscope and the fixed board keeps your hand movement predictable at high magnification, which makes tight pitch work easier to control. Preheat the board evenly, keep your nozzle moving, and let the fixture carry the weight of the job so your attention stays on temperature and timing. A steady hold also protects neighbouring components from accidental knocks when you pull a chip.
Size, Weight and Choosing the Right 2UUL Jig
The BH31 measures 135 x 63 x 17 mm and weighs 245 g net, so it sits beside a hot air station without crowding your tools. Compare it with the 2UUL BH21 OX Jig, a universal holder at 89 x 130 x 20 mm and 380 g, and the BH30 Smile JIG Mini at 96.5 x 49 x 20 mm and 128 g. If you hold single phone boards and BGA chips most days, the BH31 gives you a balanced size. If you want a heavier base, step up the PCB holders range to the OX Jig. Add a microscope, a reliable soldering station, and a reballing kit, and you build a complete rework bench. When a phone stays dead after flash and the hardware fault traces to memory or its pads, move on to eMMC programmers, ISP pinout tools, or UFS adapters to rewrite the firmware once the chip sits correctly on the board. Technicians in a shared workshop also benefit from a jig that needs no setup, because anyone on the team can pick it up and use it immediately.
| Weight | 0.245 kg |
|---|
Key Features
- ✓Two-way clamp for quick fixing of phone PCBs and IC chips
- ✓V-slot design for fast, accurate positioning
- ✓Anti-slip base pad for a stable hold
- ✓Heat-resistant, deformation-resistant construction
- ✓Easy-clean surface for flux and solder residue
- ✓Suits a wide range of IC and motherboard sizes
- ✓Compact 135 x 63 x 17 mm body with 245 g net weight
- ✓No installation required
Specifications
| Brand | 2UUL |
|---|---|
| Model | BH31 |
| Category | PCB Holders |
| Compatibility | Universal mobile phone PCB and IC chip holder (not device-specific) |
| Technology | Two-way V-slot clamp with anti-slip base |
| Dimensions | 135 x 63 x 17 mm |
| Weight | 245 g (net) |
Common Repair Uses
- ✓Holding boards and chips steady during soldering and rework
- ✓BGA chip soldering
- ✓Reballing
- ✓Chip replacement
- ✓Motherboard fixing during hot air rework
- ✓Microsoldering support at the soldering station
- ✓Fixing boards for IC removal and replacement on dead phone and charging issue jobs
Compatible Devices
- ✓Universal — not device-specific; holds phone and tablet boards and BGA ICs
- ✓Mobile phone motherboards of most sizes
- ✓Tablet motherboards
- ✓BGA IC chips on phone boards
- ✓CPU chips on phone boards
- ✓IC chips of various sizes
- ✓Boards for soldering, reballing, and chip replacement work
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the 2uul BH31 hold a board for hot air BGA rework?
What are the dimensions and weight of the 2uul BH31 Smile JIG?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



