Relife RL-044 XM14 SM8350 BGA Reballing Stencil
₨ 599
Relife RL-044 XM14 Stencil for Snapdragon 888 Boards
The Relife RL-044 XM14 stencil is a 0.12mm steel SM8350 BGA reballing plate for Snapdragon 888 boards in the Xiaomi Mi 11, Mi 11 Ultra, Mi 11 Pro, Mi 11X Pro and Redmi K40 Pro. It gives your bench a footprint-matched template for CPU reballing, so solder balls land on the right pads after a hot air lift. Technicians in Pakistan use it for dead phone, hang on logo and boot loop issue repairs that trace back to cracked SoC joints. XM14 is one plate from the 15-piece RL-044 Xiaomi series, so you buy exactly the footprint you service.
Out of stock
Relife RL-044 XM14 Stencil for Snapdragon 888 Boards
The Relife RL-044 XM14 stencil is a 0.12mm steel SM8350 BGA reballing plate for Snapdragon 888 boards in the Xiaomi Mi 11, Mi 11 Ultra, Mi 11 Pro, Mi 11X Pro and Redmi K40 Pro. It gives your bench a footprint-matched template for CPU reballing, so solder balls land on the right pads after a hot air lift. Technicians in Pakistan use it for dead phone, hang on logo and boot loop issue repairs that trace back to cracked SoC joints. XM14 is one plate from the 15-piece RL-044 Xiaomi series, so you buy exactly the footprint you service.
Long Description:
SM8350 BGA Reballing Stencil for Xiaomi Mi 11 and Redmi K40 Pro Boards
The Relife RL-044 XM14 is an SM8350 BGA reballing stencil for Snapdragon 888 boards in the Xiaomi Mi 11 family and the Redmi K40 Pro. It sits in the RL-044 Xiaomi series, a numbered range of 0.12mm steel plates where each plate matches one CPU footprint. You pick XM14 when the chip under your hot air nozzle reads SM8350, and you skip the guesswork a universal mesh forces on you. Repair shops in Pakistan that handle flagship Xiaomi boards get a repeatable reballing step from this plate: every ball lands on its pad, and every board gets the same result.
Footprint Match and Technical Highlights
XM14 carries the SM8350 layout. Xiaomi paired that Qualcomm Snapdragon 888 SoC with the Mi 11, Mi 11 Ultra, Mi 11 Pro, Mi 11X Pro, Mi 11i and Redmi K40 Pro, so one plate covers six device names on your counter. The RL-044 Xiaomi series uses round and square apertures with a half-cut design that blocks leftover tin where a footprint calls for it, and Relife calibrates each plate against the original chip drawing. The 0.12mm steel stays flat and rigid under hot air, so the stencil lifts away cleanly once the solder balls reflow. Relife rates the RL-044 range for high temperature and wear resistance, which matters when one XM14 serves many boards on your bench.
Where XM14 Fits in Your Mobile Repair Workflow
Most XM14 jobs start with a dead phone, a hang on logo fault or a boot loop issue after a drop or heat exposure, where cracked solder joints under the SoC point to a hardware fault. You confirm the fault first with a multimeter, then open the board under a microscope. A hot air station lifts the CPU, a soldering station and flux clean the pads, and a PCB holder keeps the board steady while you align XM14 over them. When IC change karna is not the plan and the original CPU goes back on, you apply paste or solder balls, reflow, peel the stencil off and inspect every ball before you place the chip. The Mi 11 generation stores data on UFS 3.1 flash, so if the board still misbehaves after the CPU work, UFS adapters and ISP pinout tools cover your next diagnostic step. Test boxes close the loop once the phone powers up and you verify charging issue, display problem and network issue behaviour.
Picking XM14 Instead of Another Xiaomi Plate
Read the marking on the SoC before you order. XM14 covers SM8350 only, and the neighbouring plates in the XM1–XM15 range cover other Snapdragon generations, so a wrong plate leaves balls off their pads. If your counter sees Redmi Note, older Mi and Redmi K-series boards as often as Mi 11 boards, the full 15in1 XM1–XM15 set saves you a trip per job. XM14 alone suits a bench that sees flagship Mi 11 and K40 Pro boards regularly. Pair the plate with a reballing kit, quality solder balls and a stable hot air station, and you handle the Snapdragon 888 reball with the same discipline you apply to any BGA rework. Clean the plate with flux remover after each job and store it flat, because a bent stencil costs you the alignment you paid for.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Footprint-matched XM14 plate for the Qualcomm Snapdragon 888 SM8350 CPU
- ✓0.12mm steel construction for a flat, rigid reballing surface
- ✓Round and square apertures with half-cut design from the RL-044 Xiaomi series
- ✓Plate calibrated against original chip drawings
- ✓High temperature and wear resistance for repeated hot air cycles
- ✓Covers Xiaomi Mi 11, 11 Ultra, 11 Pro, 11X Pro, 11i and Redmi K40 Pro boards
- ✓One plate from the 15-piece XM1–XM15 Relife RL-044 Xiaomi series
- ✓Suited to hot air station and reballing kit workflows on a repair bench
Specifications
| Brand | Relife |
|---|---|
| Model | RL-044 XM14 |
| Category | BGA Reballing Stencil |
| Compatibility | Xiaomi Mi 11 series and Redmi K40 Pro boards with Qualcomm Snapdragon 888 SM8350 |
| Supported Devices | Xiaomi Mi 11, Mi 11 Ultra, Mi 11 Pro, Mi 11X Pro, Mi 11i, Redmi K40 Pro |
| Technology | Steel mesh BGA reballing, 0.12mm thickness |
| Material | Steel |
Common Repair Uses
- ✓CPU-level reballing on SM8350 Xiaomi boards
- ✓SM8350 CPU reballing after hot air removal
- ✓Dead phone repair caused by cracked CPU solder joints
- ✓Hang on logo and boot loop issue repair at CPU level
- ✓Pad cleaning and solder ball placement before CPU reflow
- ✓Hardware fault recovery after drop or heat damage
- ✓Reballing a lifted CPU for reuse on the same board
- ✓Rework of Xiaomi flagship boards in repair shops and service centers
- ✓Training bench practice on BGA reballing technique
Compatible Devices
- ✓Xiaomi Mi 11 series and Redmi K40 Pro boards built on the Qualcomm Snapdragon 888 SM8350 CPU
- ✓Xiaomi Mi 11
- ✓Xiaomi Mi 11 Ultra
- ✓Xiaomi Mi 11 Pro
- ✓Xiaomi Mi 11X Pro
- ✓Xiaomi Mi 11i
- ✓Redmi K40 Pro
- ✓Qualcomm Snapdragon 888 SM8350 CPU footprint
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which chipset does the Relife RL-044 XM14 stencil support?
Can I use the XM14 stencil on other Xiaomi or Redmi boards?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



