2UUL FX-001 0.01mm Jumper Wire 100m for Mobile PCB Repair

₨ 800

0.01mm Ultrafine Jumper Wire

The 2UUL FX-001 gives you 100 metres of 0.01mm bare conductive wire for precise jumper repairs on mobile phone and PCB boards. You use it to rebuild lifted BGA pads, bridge cut traces, and repair fingerprint or CPU solder joints on iPhone and other phone motherboards. The strand has no breakpoints, resists breaking, stays non-magnetic, and takes tin easily, so you skip paint scraping and solder it straight onto the pad. Mechanicpk supplies this FX-001 spool to Pakistani repair shops and technicians who need dependable fine-pitch repair consumables on the bench.

In stock

14 People watching this product now!
Description

0.01mm Jumper Wire for Mobile Repair: 2UUL FX-001 Technical Overview

The 2UUL FX-001 is a 0.01mm jumper wire for mobile repair, built for one job: restoring broken connections on a logic board where a standard wire cannot fit. The spool holds 100 metres of uninsulated conductor, so one roll covers a long run of trace and pad repairs across iPhone and other mobile phone motherboards. When a lifted pad leaves you with a dead phone, or a charging issue traces back to a torn track, you bridge the gap with a strand finer than the pad itself. Mechanicpk supplies the FX-001 to technicians and repair shops across Pakistan who already understand why wire diameter matters on BGA and fine-pitch joints, and who want a consistent spool they can reorder.

Wire Construction and Soldering Behaviour

2UUL supplies the FX-001 as a bare, non-insulated strand with a 0.01mm diameter. The listed traits describe a wire with no breakpoints along its length, good toughness, non-magnetic behaviour, and low solder resistance. The strand is easy to tin, and it welds directly onto the pad without a breakpoint. The wire carries no enamel coating, so you never scrape paint before you solder. That removes a common failure point, because scraping a strand this thin often snaps it, and a break halfway through a jumper wastes the repair time you already spent. Since the conductor stays uninsulated, you control the routing yourself. Handle the strand with fine tweezers, lay it flat against the board, keep it clear of neighbouring pads, and secure it with UV solder mask or a small drop of glue once your multimeter confirms continuity.

Using 0.01mm Jumper Wire for Mobile Repair at the Bench

Most FX-001 work happens under a microscope with a soldering station or a fine-tip iron. Typical jobs include rebuilding a lifted BGA pad after IC change karna, bridging a cut trace on a charging line, and reconnecting pads on a fingerprint flex or similar fine connector. Clamp the board in a PCB holder first, clean the area, and expose the bare copper trace or pad. Then tin the pad, anchor one end of the wire, route it to the target point, and trim the excess. Finish by checking continuity and testing for shorts between neighbouring points. When a CPU shows peeled solder joints, pair the wire with a reballing kit and a hot air station so you can rework the chip after the pad repair. If a dead phone still draws no current after the jumper lagana step, move from the wire to board-level diagnosis with your multimeter and power supply.

Choosing the 0.01mm Diameter Over Other 2UUL Options

2UUL sells this wire family in 0.009mm, 0.01mm, and 0.02mm diameters, with conductive and insulated variants and an ultrasoft version. The FX-001 sits at the middle diameter and ships uninsulated. Pick it when a 0.02mm strand feels too bulky for your pad pitch, such as fine iPhone board work, and when you can route the jumper without crossing other copper. Because a bare strand that touches an adjacent pad creates a short, plan the path before you solder. For routes that must cross other copper, choose an insulated 2UUL variant instead. Mechanicpk lists the FX-001 with related soldering and rework consumables, so you can add flux, fine tweezers, and a PCB holder to the same order. Each 100-metre spool keeps your bench stocked for a long stretch of daily repairs.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Ultrafine 0.01mm wire diameter for fine-pitch pads
  • 100-metre spool for long-term bench use
  • Non-insulated bare conductor
  • No breakpoint along the wire
  • Good toughness
  • Non-magnetic
  • Low solder resistance
  • Easy to tin, with no paint scraping

Specifications

Brand2UUL
ModelFX-001
CategoryJumper Wire / PCB Repair Consumables
CompatibilityUniversal — not device-specific
Supported DevicesMobile phone and computer PCBs, including iPhone motherboards
TechnologyUltrafine, non-insulated, non-magnetic conductive jumper wire
DimensionsWire diameter 0.01mm; length 100m

Common Repair Uses

  • Fine-pitch jumper and pad repair on phone and PCB boards
  • Rebuilding lifted BGA pads
  • Bridging cut PCB traces
  • Repairing charging line tracks
  • CPU solder joint peeling repair
  • Fingerprint board pad repair
  • Reconnecting damaged flex cable contacts
  • Restoring IC pad connections after IC change
  • Micro soldering on iPhone motherboards

Compatible Devices

  • Universal use on mobile phone and computer PCBs (not tied to specific models)
  • iPhone motherboards
  • Android and other mobile phone logic boards
  • Computer and laptop PCBs
  • CPU and BGA chip solder pads
  • Fingerprint sensor board pads
  • PCB tracks and traces
  • Flex cable contact pads
  • Fine-pitch IC pads

FAQ

What is the product name?
The product name is 2UUL FX-001 Ultrafine Conductive Jumper Wire 0.01mm 100m.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is FX-001.
What is this product used for?
This product is used for jumper repairs on mobile phone and PCB boards, including trace repair and BGA pad rebuilding.
Which devices are compatible with this product?
This product is universal and not device-specific. You use it on mobile phone motherboards, including iPhone boards, and on computer PCBs.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the 2UUL FX-001 jumper wire insulated?
No. The FX-001 is a non-insulated bare wire, so you route it clear of neighbouring pads and secure it after soldering. 2UUL offers separate insulated variants for crossing routes.
What is the difference between 2UUL FX-001 and FX-002?
The FX-001 has a 0.01mm diameter and no insulation. The FX-002 has a thicker 0.02mm diameter and is also a conductive non-insulated wire.