Mechanic FX-201 Jumper Wire 0.01mm for Mobile PCB Repair
₨ 900
Ultra-Fine 0.01mm Jump Wire for PCB Repair
Mechanic FX-201 Jumper Wire 0.01mm gives you a 200-metre spool of ultra-fine jump wire for board-level mobile repair. At 0.01mm, the wire runs between tight solder pads on iPhone and Android logic boards, so you can repair broken traces, lifted pads and damaged FPC contacts without bridging neighbouring points. The manufacturer’s range lists no breakpoints, good toughness, non-magnetic behaviour and low welding resistance, so the wire tins fast and holds its shape under the iron. Pair it with a microscope, a fine-tip soldering station and a PCB holder for clean results on dead phone and charging issue repairs.
Out of stock
0.01mm Jumper Wire for Mobile Repair: Mechanic FX-201 Explained
The Mechanic FX-201 Jumper Wire 0.01mm is a 200-metre spool of ultra-fine conductor made for board-level repair. If you need a 0.01mm jumper wire for mobile repair, this is the wire you pick up when a trace, pad or FPC contact is gone and a standard wire will not fit the pitch. At 0.01mm, the conductor is thinner than a human hair, so you can route it between neighbouring pads on a dense logic board without bridging them. Mechanic sells the FX-201 in a range of ultra-fine jump wires that also includes the 0.02mm FX-202 and the 0.005mm FS-205 and FX-105.
Conductor Behaviour on the Bench
The range description for Mechanic jump wire lists no breakpoints, good toughness, non-magnetic behaviour, low welding resistance and good stretchability. In practice, that means the wire tins quickly, accepts solder without fighting you, and straightens easily before you lay it down. A low-resistance joint matters on signal-level repairs, where a poor connection leaves you chasing a hardware fault that you already fixed once. Handle the wire with tweezers or by its spool, never by pinching the free end between your fingers. A wire this fine kinks and snaps under careless handling, and a snapped wire under the microscope costs you more time than a fresh cut.
Where the FX-201 Fits in a Repair Workflow
You reach for the FX-201 after diagnosis, not before it. Start with a multimeter continuity check to confirm which trace or pad has failed, then inspect the area under a microscope. When the pad has lifted or the trace has burnt through, the FX-201 rebuilds the connection from the nearest healthy point to the component pad. Technicians use this routine for FPC and FFC contact repair, fingerprint flex pads on iPhone boards, screw-hole broken traces, and pads that peeled during IC change karna work. It also supports BGA and CPU solder-point repair, where a damaged pad under or beside a chip needs a bridge before you reball. A stable PCB holder keeps the board still, and a fine-tip soldering station or hot air station completes the joint. If you run a reballing kit in the same workflow, keep the jump wire spool on the same bench tray so repairs flow without interruption.
Choosing 0.01mm Over the Other Diameters
The 0.01mm size suits dense areas where the 0.02mm FX-202 crowds the pitch, and where you need the wire to disappear between pads. The finer diameter trades strength for precision. Use the FX-201 for short signal links, pad-to-pad bridges and contact restoration, and choose a heavier conductor for power-rail jumpers that carry real current. If a charging issue traces back to a damaged power path rather than a single pad, weigh that load before you commit to an ultra-fine wire. Buy it as a consumable: a 200-metre spool covers a long run of jobs, so a repair shop or service centre can keep one on the bench and replace it on a schedule instead of waiting for it to run out mid-job.
| Weight | 0.10 kg |
|---|
Key Features
- ✓0.01mm ultra-fine diameter, thinner than a human hair
- ✓200-metre spool for long-term bench use
- ✓No breakpoints along the wire
- ✓Good toughness, resists snapping during routing
- ✓Non-magnetic wire
- ✓Low welding resistance for clean solder joints
- ✓Stretchable and easy to straighten before placement
- ✓Fits tight pad pitch on dense phone logic boards
Specifications
| Brand | Mechanic |
|---|---|
| Model | FX-201 |
| Category | Jumper Wire / Soldering Consumables |
| Compatibility | Universal — not tied to a specific phone model or chipset |
| Wire Diameter | 0.01mm |
| Length | 200m |
Common Repair Uses
- ✓Board-level trace, pad and FPC contact restoration
- ✓Repairing broken motherboard traces
- ✓Rebuilding lifted or dropped solder pads
- ✓Fingerprint flex pad repair on iPhone boards
- ✓FPC and FFC contact repair
- ✓Restoring screw-hole broken traces
- ✓BGA and CPU solder-point repair before reballing
- ✓Pad recovery after IC change karna
- ✓Signal-level jumper lagana on dead phone and hardware fault boards
Compatible Devices
- ✓Universal ultra-fine jump wire, used on iPhone and Android logic boards and FPC/FFC boards — not device-specific
- ✓Universal wire, not tied to any specific phone model or chipset
- ✓iPhone logic boards, including fingerprint flex pad repair
- ✓Android phone motherboards across brands
- ✓Mobile phone FPC and FFC boards
- ✓BGA and CPU solder-point areas on phone PCBs
- ✓Motherboard solder pads and pad drop points
- ✓Broken traces on electronic circuit boards
- ✓Motherboard screw-hole broken trace points
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How does the FX-201 0.01mm wire differ from the 0.02mm FX-202?
How do I stop 0.01mm jump wire from snapping while I solder it?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



