Amaoe SSD3 BGA Reballing Stencil 0.15mm Innogrit

₨ 1

Innogrit SSD Controller Reballing Stencil

The Amaoe SSD3 BGA Reballing Stencil gives your bench a 0.15 mm steel mesh template for reballing Innogrit SSD controller ICs, including the IG5669FAA, IG5236CAA and IG5220BAA. A fixed hole pattern keeps every solder ball in line with the pads, so you restore a removed controller without improvising a layout. The SSD3 belongs to Amaoe’s SSD1 to SSD4 stencil series, and you can confirm hole alignment under a microscope before you apply heat. Technicians who run SSD board repair next to phone board work get a precise template, and the Amaoe SSD3 BGA reballing stencil fits that workflow in Pakistan.

Out of stock

16 People watching this product now!
Description

Amaoe SSD3 BGA Reballing Stencil for Innogrit SSD Controllers

The Amaoe SSD3 BGA reballing stencil does one job: it puts a fresh, even set of solder balls on an Innogrit SSD controller after you lift the chip from the board. Amaoe cuts the template from 0.15 mm steel mesh and lays out a fixed hole pattern for the IG5669FAA, IG5236CAA and IG5220BAA controllers. Supplier listings also tie the SSD3 to LPDDR4 BGA200 and BGA345 footprints. If your bench already handles phone CPU and eMMC reballing, this stencil extends the same technique to Innogrit SSD controller work without adding a new process to learn. Mechanicpk supplies it for technicians and repair shops that treat controller reballing as a precision task, where the template, the heat profile and the pad preparation all decide the outcome.

Stencil Build and Hole Pattern

Thickness decides how much solder each pad receives, and the SSD3 uses 0.15 mm steel mesh. That thickness suits fine-pitch controller footprints, where a thicker sheet deposits too much solder and bridges neighbouring balls. The fixed hole pattern holds ball placement even across the whole array, so you align the openings to the pads once and the pattern keeps every ball in position. Amaoe sorts its SSD stencils into an SSD:1 to SSD:4 series, which means you match the stencil to the controller footprint instead of forcing one template across several chips. Before you apply heat, set the stencil on the cleaned pads and check hole alignment under your microscope. Flux on the pads helps the balls seat in the openings, and a light press on the stencil edge during reflow stops it lifting. A template that sits a fraction off ruins the reball and can scrap the controller, so the alignment check costs seconds and protects an expensive part.

Where It Fits in the SSD Repair Workflow

Controller reballing sits after removal and cleaning in the rework sequence. You lift the IC with a hot air station, clean the pads and the chip underside with your soldering station and desoldering wick, then fit the SSD3 over the chip with a holder or fixture so the template stays still. Apply the balls, reflow, lift the stencil away, and inspect every ball before you refit the controller to the board. Keep the heat gentle and even through reflow. SSD controllers sit beside memory ICs on the same board, and overheating the neighbours creates a second fault while you fix the first. A multimeter continuity check on the pads before and after the job catches lifted pads and shorts early. When a board comes in with a hardware fault after an earlier reflow, a clean reball of the controller replaces a doubtful joint with a controlled one. PCB holders keep the board flat during removal, and a reballing kit supplies the balls, flux and tools that surround the stencil.

Choosing the SSD3 for Your Bench

Match the stencil to the footprint before you order. The supplier information lists IG5669FAA, IG5236CAA and IG5220BAA for the SSD3 and advises confirming the footprint on similar controllers from the same series. Read the marking on your controller, compare it with that list, and choose the SSD3 only when the part number lines up. Workshop owners who stock Mechanicpk’s soldering and reballing range can pair the SSD3 with the SSD1, SSD2 and SSD4 stencils and cover several SSD controller jobs with a small, organised set of templates. The pack contains one stencil and no balls or flux, so budget for consumables in the same order. Distributors who resell to workshops can list the SSD3 beside Reballing Kits and Microscopes, because buyers searching for one usually need the others. Clean the stencil after every use and store it flat, and it stays ready for the next reball.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.15 mm steel mesh stencil for fine-pitch controller footprints
  • Fixed hole pattern that keeps solder ball placement even
  • Layout for Innogrit IG5669FAA, IG5236CAA and IG5220BAA controllers
  • Supplier-listed LPDDR4 BGA200 and BGA345 footprint coverage
  • Hole alignment can be checked under a microscope
  • Part of the Amaoe SSD1 to SSD4 stencil series
  • Brand-new Amaoe stencil for SSD board repair and PCB rework
  • Supplied as a single stencil

Specifications

BrandAmaoe
ModelSSD3
CategoryBGA Reballing Stencil
CompatibilityInnogrit SSD controller ICs IG5669FAA, IG5236CAA, IG5220BAA
Supported DevicesInnogrit-controller SSD boards
TechnologyBGA reballing, 0.15 mm steel mesh stencil, fixed hole pattern
MaterialSteel mesh

Common Repair Uses

  • Reballing and rework of SSD controller ICs
  • Reballing an Innogrit SSD controller after IC removal
  • Restoring a controller that needs fresh solder balls after an earlier reflow
  • Reballing LPDDR4 BGA200 and BGA345 footprints
  • Checking hole-to-pad alignment under a microscope before reflow
  • Re-tinning a cleaned controller during SSD board repair
  • Preparing a controller for refit after a hardware fault repair

Compatible Devices

  • Innogrit SSD controller ICs, with the footprint to confirm on other controllers from the same series
  • Innogrit IG5669FAA SSD controller
  • Innogrit IG5236CAA SSD controller
  • Innogrit IG5220BAA SSD controller
  • LPDDR4 BGA200 footprint (named in supplier listings)
  • LPDDR4 BGA345 footprint (named in supplier listings)

FAQ

What is the product name?
The product name is Amaoe SSD3 BGA Reballing Stencil.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is SSD3.
What is this product used for?
This product is used for reballing Innogrit SSD controller ICs with a 0.15 mm steel mesh BGA stencil.
Which devices are compatible with this product?
This product is compatible with Innogrit IG5669FAA, IG5236CAA and IG5220BAA SSD controller ICs. Confirm the footprint before you use it on other controllers from the same series.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Innogrit controller chips does the Amaoe SSD3 stencil support?
The listed controllers are IG5669FAA, IG5236CAA and IG5220BAA. Read the marking on your controller and compare it with this list before you order.
Does the Amaoe SSD3 stencil cover BGA200 and BGA345 packages?
Supplier listings name LPDDR4 BGA200 and BGA345 for the SSD3, but they publish no pitch or ball dimensions. Check the footprint on your chip against the stencil before you reball.