Koocu V502 Soldering Iron 30W/40W/60W Ceramic Heater
₨ 500
Koocu V502 Mobile Repair Soldering Iron
The Koocu V502 soldering iron brings a four-core ceramic heating core to your mobile repair bench in a lightweight pen-style body. Pick the 30W, 40W or 60W version to match your workload, then set the temperature anywhere between 200°C and 480°C. The iron holds ±2°C stability in still air and keeps tip-to-ground impedance below 2Ω, so it suits work near sensitive boards. Technicians use it for charging port replacement, pad reflow, jumper wire repair and general PCB soldering on smartphones, tablets and small electronics. A LED indicator shows when the iron is powered and working.
Out of stock
Koocu V502 Soldering Iron for Precise Mobile Board Work
The Koocu V502 soldering iron gives your workshop a mains-powered, pen-style iron built around a four-core ceramic heating core. Koocu ships it in 30W, 40W and 60W versions, so you match wattage to the job instead of forcing one iron to cover every repair. If you handle charging port replacement, flex connector pads and jumper wire repair every day, this iron delivers a controllable heat source in a light, easy-to-hold body.
Heating Core and Temperature Control
The ceramic heating core reaches working temperature quickly, which keeps your bench moving between dead phone jobs. You set the temperature between 200°C and 480°C, a range that covers leaded solder and the higher melting point of lead-free alloys. Temperature stability holds at ±2°C in still air with no load, and accuracy sits at ±10°C. Those figures matter when you work on thin pads, because a stable tip lowers the risk of lifting a track.
The iron also carries protection for the boards you touch. Tip-to-ground impedance stays below 2Ω and tip-to-ground voltage stays below 2mV, which limits leakage near sensitive ICs and connectors. The V502 runs on 220V AC ±10% at 50Hz. A LED indicator shows the iron’s working state, and the body weighs about 131g, so your wrist stays relaxed through long sessions.
Where the V502 Fits in the Repair Workflow
You reach for this iron when the fault sits at a specific pad, port or track. Charging issue on a phone? Remove the old port, clean the pads and fit the new one with controlled heat. A broken track on the mainboard? Jumper lagana with fine wire, then reflow the joint cleanly. Small components and shield frames also come off and go back with the right tip and wattage.
The V502 does not replace a hot air station for BGA ICs, so pair it with one from the Hot Air Stations range when you plan an IC change karna job on larger chips. Keep a Multimeter nearby to confirm continuity after every joint, and a Microscope to inspect pads before you power the board. A PCB Holder keeps the board steady while you solder, and a Reballing Kit completes the bench for chip-level work. If you outgrow a single iron, the Soldering Stations category offers the upgrade path to digital, closed-loop control.
Choosing the Right Wattage
Wattage changes how the iron behaves on heavy copper. Choose 30W for fine pads, flex connectors and low-mass joints where you want gentle heat. Choose 40W as an all-round bench iron for ports, buttons and wires. Choose 60W when you work on ground planes, shield cans and large pads that pull heat away quickly. Many repair shops keep two wattages on the bench and swap between them as the board demands.
For Pakistani technicians who run a busy shop, the V502 offers a practical balance: the same ceramic heater technology across all three wattages, a familiar pen layout and a temperature range wide enough for daily repair soldering. Buy it as a primary iron for a new bench or as a dependable spare for your existing setup.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Four-core ceramic heating core for fast, even heat
- ✓Available in 30W, 40W and 60W versions
- ✓Temperature range of 200–480°C
- ✓±2°C temperature stability in still air with no load
- ✓Tip-to-ground impedance below 2Ω and voltage below 2mV for safer board contact
- ✓LED indicator shows working state
- ✓Lightweight pen-style body of about 131 g
- ✓Suited for mobile phones, computers, cameras and other electronics
Specifications
| Brand | Koocu |
|---|---|
| Model | V502 |
| Category | Soldering Irons |
| Compatibility | Universal — not device-specific |
| Technology | Four-core ceramic heating core, temperature range 200–480°C, stability ±2°C (still air, no load), accuracy ±10°C, tip-to-ground impedance |
| Input Voltage | 220V AC ±10%, 50Hz |
| Power Rating | 30W / 40W / 60W (version-dependent) |
| Weight | Approx. 131 g |
Common Repair Uses
- ✓Charging port replacement after a charging issue
- ✓Pad reflow and pad cleaning on damaged connectors
- ✓Jumper wire repair on broken tracks
- ✓Flex connector and battery connector soldering
- ✓Small component removal and replacement
- ✓Shield frame touch-up and tinning
- ✓General PCB soldering and wire attachment
- ✓Hardware fault diagnosis and rework follow-up
Compatible Devices
- ✓Universal soldering iron — works on any board that accepts standard soldering, not limited to specific models or chipsets
- ✓Android smartphone mainboards
- ✓iPhone mainboards
- ✓Feature phone boards
- ✓Tablet circuit boards
- ✓Charging port and battery connector pads
- ✓Computer and laptop circuit boards
- ✓Camera and small electronic device boards
- ✓General electronic gadgets and PCB assemblies



