Mechanic HX-T100 0.3mm Solder Wire 55g Sn63/Pb37
₨ 499
0.3mm Rosin Core Solder Wire
The Mechanic HX-T100 is a 0.3mm solder wire for mobile repair, built for technicians who solder fine pads on phone motherboards. The 55g reel uses a Sn63/Pb37 eutectic alloy with a rosin flux core and melts at 183°C. That low melting point keeps heat exposure short around ICs, flex connectors, and BGA pads. The thin 0.3mm wire lets you control the amount of solder you feed to each joint, so you avoid bridges between tight pins. Use it for jumper wires, charging port pads, small SMD components, and reflow touch-ups on Android and iPhone boards. Pair it with a soldering station, hot air station, and microscope for clean, repeatable joints at your repair bench.
Out of stock
Mechanic HX-T100 0.3mm Solder Wire for Fine Mobile Board Work
Phone boards leave no room for oversized solder. The Mechanic HX-T100 is a 0.3mm solder wire for mobile repair that gives you precise feed control on small pads, tight pin rows, and shielded areas. The alloy is Sn63/Pb37 with a rosin flux core, and it melts at 183°C. A 55g reel gives a shop enough supply for daily soldering across many repair jobs.
Sn63/Pb37 Eutectic Alloy Behaviour
Sn63/Pb37 is a eutectic composition, so the wire turns from solid to liquid at a single temperature, 183°C, with no pasty stage in between. That behaviour gives you quick wetting and a clean, bright joint when your iron or hot air tool holds a steady temperature. You avoid dull, grainy joints caused by a slow transition. The lower melting point also reduces thermal stress on the board and on heat-sensitive parts near the work area. Because the alloy contains lead, treat it as leaded solder and use proper ventilation at your bench.
Why 0.3mm Suits Phone Motherboard Repair
Wire diameter decides how much solder reaches the joint on every feed. A 0.3mm strand lets you add a small, measured amount of solder to a charging connector pad, a battery connector, a flex socket, or a jumper point without flooding neighbouring pins. For BGA solder wire use, the fine gauge helps you tin lifted pads and touch up reballed areas under a microscope. The rosin core carries the flux with the wire, so you do not need to apply flux separately for quick touch-ups. For larger shielding cans or heavy ground pads, switch to a thicker gauge from the same HX-T100 range.
Fit in the Repair Workflow
Technicians use this wire at several points in a board-level job. You tin a pad after IC removal, fix a broken trace with a jumper, repair a charging port, or re-solder a loose component after a dead phone diagnosis. The wire works with a temperature-controlled soldering iron or station, and with a hot air station for reflow touch-ups. Hold the board in a PCB holder, check the joint under a microscope, and test continuity with a multimeter before you close the phone. Stock a few diameters beside this reel if your shop handles both fine SMD work and heavier hardware fault repair. If you also work with reballing kits, keep this wire near your bench for pad preparation before stencil work.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Sn63/Pb37 eutectic alloy with a single 183°C melting point
- ✓Rosin flux core inside the wire
- ✓0.3mm fine diameter for controlled solder feed
- ✓55g reel sized for daily workshop use
- ✓Good solderability with bright solder joints
- ✓Low-spatter, non-corrosive soldering action
- ✓Suited to mobile phone motherboard and BGA chip repair
- ✓Same HX-T100 range offers thicker diameters for heavier joints
Specifications
| Brand | Mechanic |
|---|---|
| Model | HX-T100 |
| Category | Solder Wire / Soldering Consumables |
| Compatibility | Universal — not device-specific; suits any board or component that accepts Sn63/Pb37 solder |
| Technology | Sn63/Pb37 eutectic rosin core solder |
| Material | Tin-lead alloy (63% Sn, 37% Pb) with rosin flux core |
| Wire Diameter | 0.3mm |
| Melting Point | 183°C |
| Weight | 55g |
Common Repair Uses
- ✓Fine-pitch soldering and board-level repair work on mobile phone motherboards
- ✓Tinning pads after IC removal
- ✓BGA pad touch-up after reballing
- ✓Jumper wire lagana on broken traces
- ✓Charging port pad soldering for charging issue repair
- ✓Battery connector re-soldering
- ✓Small SMD component replacement
- ✓Loose joint repair on dead phone boards
- ✓Flex connector pad soldering for display problem repair
Compatible Devices
- ✓Universal solder wire — not tied to specific models; used on mobile phone motherboards and general electronics circuit boards
- ✓Android smartphone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno, Xiaomi)
- ✓iPhone logic boards for pad and connector soldering
- ✓Charging port and flex connector pads on mobile PCBs
- ✓Battery connector pads
- ✓Small SMD components on phone boards
- ✓BGA pads on mobile motherboard ICs
- ✓Jumper and trace repair points
- ✓General electronics circuit boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is Mechanic HX-T100 solder wire leaded or lead-free?
What is the melting point of Mechanic HX-T100 0.3mm solder wire?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



