Mijing FX-04 0.04mm Copper Flying Jumper Wire 100m

₨ 1

Mijing FX-04 Copper Wire, 0.04mm x 100m

The Mijing FX-04 copper flying jumper wire gives your repair bench a 0.04mm conductor on a 100-meter spool. High ductility and low impedance keep your bridged tracks stable, and the wire tins easily without paint scraping, so you skip a prep step on every jumper. Use it for mainboard flying wire maintenance, chip patching, broken trace rebuilds, Touch ID repairs and battery board work on mobile phone and computer motherboards. Mechanicpk supplies the FX-04 for Pakistani technicians who need a consistent, workshop-ready jumper wire for daily PCB repair.

Out of stock

17 People watching this product now!
Description

Mijing FX-04 Copper Flying Jumper Wire for Precision Motherboard Repair

The Mijing FX-04 copper flying jumper wire delivers a 0.04mm copper conductor on a 100-meter spool. It targets the trace, pad and connection repairs that separate a recovered board from a dead phone. If you rebuild broken tracks on mobile phone, computer and battery boards every week, this gauge gives you a sturdier bridge than hair-thin wires while it still fits the pads you meet on most boards. Mechanicpk lists the FX-04 for Pakistani workshops that want a dependable jumper wire at a consistent diameter, spool after spool.

Technical Profile of the 0.04mm Copper Conductor

Mijing rates the FX-04 at a 0.04mm wire diameter with high ductility and low impedance. Low impedance keeps the signal path clean when you bridge a data or power line, so the repaired track behaves like the original instead of adding resistance. High ductility lets you bend, stretch and route the wire around components without it snapping at the first tight corner. The copper conductor tins easily, and it takes solder without scraping off any paint coat, which removes a prep step from every jumper you lay. The 100-meter length covers a heavy repair schedule, so one spool keeps a busy bench running for a long time.

Where the FX-04 Fits in the PCB Repair Workflow

The FX-04 enters your workflow after you diagnose the fault and before you test the board. You trace the broken line with a multimeter, expose the pads on both ends, and lay the flying wire between them. Typical jobs include mainboard flying wire maintenance, chip patching, rebuilding broken traces, jumper modifications and BGA rework connections. You can also use this wire type for Touch ID repairs and battery board work. Boards with a charging issue, display problem or network issue often carry a lifted pad or burnt track, and jumper lagana on those faults decides whether a hardware fault board returns to the customer or stays on the shelf. A single spool covers all of these jobs, so you keep one consumable ready instead of juggling several.

Bench Handling and Soldering Behavior

Pair the FX-04 with a temperature-controlled soldering station and a microscope for pad-level work. Cut a length slightly longer than the gap, tin the end, and tack it to the first pad with a fine tip. Route the wire along the board surface, trim it to length, and tack the second end. Clamp the board in a PCB holder so your hands stay steady, and bring in a hot air station only when you need to lift components around the repair. Clean the flux residue before you power up, then check continuity with a multimeter across both pads. Because the wire tins without paint scraping, your iron time per joint stays short, which helps protect fragile pads from heat.

Choosing Your Gauge Within the Jumper Wire Range

The FX-04 sits at the sturdier end of the fine jumper wire range. When a pad or track measures wider than a hair, 0.04mm gives you mechanical strength and easy handling. When you chase microscopic BGA pads or fingerprint flex points, you step down to a finer gauge. Stock both and match the wire to the pad. Reballing kits and the rest of your soldering and reballing setup complete the bench around it.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • 0.04mm copper conductor
  • 100-meter spool length
  • High ductility for bending and routing
  • Low impedance for clean signal paths
  • Tins easily without paint scraping
  • Solders directly with no pre-cleaning step
  • Resists breaking and stretches without snapping
  • Suits mobile, computer, battery and Touch ID repair work

Specifications

BrandMijing
ModelFX-04
CategoryJumper Wire / Flying Wire
CompatibilityUniversal — not device-specific
MaterialCopper
Wire Diameter0.04mm
Length100m

Common Repair Uses

  • Flying wire and jumper work on mobile and computer PCBs
  • Mainboard flying wire maintenance
  • Broken trace rebuilding
  • Chip maintenance and patching
  • Jumper modifications
  • BGA rework connections
  • Touch ID jump wire repair
  • Battery board connection repair
  • Lifted pad bridging

Compatible Devices

  • Universal — not device-specific; suits mobile phone motherboards, computer motherboards, battery boards and Touch ID connections
  • Mobile phone motherboards
  • Computer motherboards
  • Phone battery boards and battery connector pads
  • Touch ID / fingerprint flex connection points
  • Broken tracks on logic boards
  • BGA rework connection points
  • Chip patching points on mainboards
  • Lifted or damaged pads on repair boards

FAQ

What is the product name?
The product name is Mijing FX-04 Copper Flying Jumper Wire.
What is the brand of this product?
The brand of this product is Mijing.
What is the model of this product?
The model of this product is FX-04.
What is this product used for?
This product is used for mainboard flying wire maintenance, chip patching and broken trace repair on mobile phone and computer motherboards.
Which devices are compatible with this product?
This product suits mobile phone motherboards, computer motherboards, battery boards and Touch ID connections. It is universal and not tied to specific device models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What diameter and spool length does the Mijing FX-04 jumper wire have?
The Mijing FX-04 has a 0.04mm wire diameter and comes on a 100-meter spool.
Do I need to scrape the coating off the FX-04 wire before soldering?
No. The FX-04 tins easily without paint scraping, so you can solder it directly onto the pad.