SUNSHINE SS-719 Pentalobe 0.8 Magnetic Aluminum Screwdriver
₨ 1
SUNSHINE SS-719 Pentalobe 0.8 Screwdriver for Apple Repair
The SUNSHINE SS-719 Pentalobe 0.8 magnetic aluminum screwdriver gives your bench a dedicated tip for Apple pentalobe fasteners. Its slim waist and anti-slip handle keep your grip steady through repeated turns, and the magnetic hold lets you lift small screws without dropping them into the housing. Use it to open bottom-edge screws during charging port, battery, and dead phone diagnostics. The tip belongs to the SS-719 series, which also includes Cross 1.5, Cross 1.2, Torx 2, and Tri Wings 0.6 variants.
Out of stock
Pentalobe 0.8 Screwdriver for Mobile Repair Workflows
A pentalobe 0.8 screwdriver is one of the first tools you reach for when an Apple device arrives with its bottom edge sealed. The SUNSHINE SS-719 pentalobe 0.8 screwdriver puts that exact tip on a magnetic aluminum handle, so you can open the housing, reach the connector flex, and close it again without stripping a fastener. Your repair bench gains a dedicated tool instead of a general bit that wobbles inside the screw head. Expect this driver to see daily use on charging issue jobs, battery replacements, and any dead phone that needs the lower assembly removed first. Because the tip is sized for one fastener family, you keep accuracy across repeated sessions rather than fighting a loose fit.
Where the 0.8 Tip Fits in the Repair Sequence
Most bottom-edge jobs start at the fastener and end at the fastener. You loosen the pentalobe screws first, lift the lower assembly carefully, and then disconnect the battery or charging flex before you touch anything else. A correct tip matters at this stage because a worn or mismatched bit can cam out and chew the screw recess, turning a five-minute job into a board-level extraction. Your workflow speeds up when the tip seats square in the head from the first turn. Keep the 0.8 tip reserved for pentalobe work so its size stays accurate across many sessions. This step belongs to disassembly and screw management, so it comes before board diagnostics, soldering, and any IC or CPU-level repair. Plan the screw sequence before you start, and sort fasteners by position in a tray so reassembly stays clean. Mark the position of any screw that differs in length, because a swapped fastener can crack the housing or interfere with the display.
Handle, Shaft, and Magnetic Hold
The SS-719 handle uses a small waist design with an anti-slip grip, which reduces hand slip when you apply steady downward pressure on a fastener. The aluminum body keeps the driver light, so long sessions at the bench feel less tiring on your wrist. The shaft is made from S2 steel, a material chosen for hardness and wear resistance on fine tips. The magnet helps you lift a screw from a bench mat and place it in a tray without fumbling. Inspect the tip after heavy use for chipping or rounded edges, since a damaged pentalobe tip deforms the screw recess quickly and makes later removals harder. Store the driver away from metal filings and loose debris, because particles can cling to the magnet and interfere with your next session. Wipe the handle after oily or dusty work so the grip keeps its feel.
Pairing the 0.8 Tip With the Rest of the SS-719 Series
The SS-719 series includes Cross 1.5, Cross 1.2, Torx 2, and Tri Wings 0.6 variants, so the family covers several common device fasteners. Buy the tip size that matches your most frequent job first, then expand the set as your repair volume grows. Many technicians keep a pentalobe driver beside a precision bit kit, a magnetic mat, and plastic spudgers for opening the case. A microscope lets you inspect the screw head before you turn it, which reduces cam-out damage on small fasteners and helps you spot a stripped recess early. Once your work moves into board-level repair, a hot air station and a soldering station take over from the screwdriver, so plan your bench in that order. This driver handles disassembly, not diagnostics or component replacement, so treat it as the first link in your repair chain.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Pentalobe 0.8 tip for Apple bottom-edge fasteners
- ✓Magnetic tip holds screws during removal and reinstallation
- ✓Aluminum handle for a light, comfortable grip
- ✓Slim waist design with anti-slip handle surface
- ✓S2 steel shaft for wear resistance on fine tips
- ✓Part of the SS-719 series with Cross, Torx, and Tri Wings options
Specifications
| Brand | SUNSHINE |
|---|---|
| Model | SS-719 |
| Category | Screwdriver |
| Compatibility | Pentalobe 0.8 fastener size |
| Material | S2 steel shaft, aluminum handle |
| Weight | 0.15 kg |
Common Repair Uses
- ✓Verified workflows for this tip size.
- ✓Removing bottom-edge screws to access the charging port flex
- ✓Opening the lower assembly to reach the battery connector
- ✓Disassembling iPhone housings during a dead phone diagnosis
- ✓Removing bottom-case screws on MacBook repairs before board work
- ✓Clearing a charging issue caused by a loose or damaged port assembly
Compatible Devices
- ✓Verified scope is the Pentalobe 0.8 fastener size, used on Apple devices.
- ✓Apple iPhone bottom-edge Pentalobe screws
- ✓Apple MacBook bottom-case Pentalobe fasteners
- ✓Pentalobe 0.8 fasteners on Apple-family electronics
- ✓Universal for any device using a 0.8 Pentalobe head
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which other tip sizes come in the SS-719 series?
Is this driver sold as a single tip or a full set?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



