Mijing Phantom SS2 IC Pad Cleaning Steel Brush 2in1
₨ 1,400
Mijing Phantom IC Pad Cleaning Steel Brush 2in1
The Mijing Phantom SS2 pairs an ultra-fine steel wire brush with a sideburns brush, so you clean IC pads and sweep away dust with one set. The 0.08mm steel bristles remove glue, leftover tin, and solder residue from CPU and IC pads on mobile phone motherboards. The bristles carry an anti-static design and hold their shape from -20°C to 550°C, which lets you brush a chip while it sits on a heating platform. You get a colorful handle for quick identification and a universal tool that fits any phone brand. Order it from Mechanicpk for your repair bench.
Out of stock
IC Pad Cleaning Steel Brush for Flat, Residue-Free Solder Pads
The Mijing Phantom SS2 is an IC pad cleaning steel brush made for the step that decides whether a chip swap holds: pad preparation. When you lift a CPU, eMMC, or power IC from a dead phone board, glue and old tin stay behind on both the pad and the chip. This 2in1 set gives you a steel wire brush for stubborn residue and a sideburns brush for dust, so you finish the cleanup in one pass at your repair bench. Mechanicpk supplies it for technicians who run hot air or a preheating platform on every IC job.
0.08mm Steel Wire Bristles for Fine-Pitch Pads
Mijing builds the steel brush with imported ultra-fine steel wire bristles that measure 0.08mm and sit closely together. The wire keeps the rigidity of steel and still flexes enough to treat each chip gently, so you remove residue without scouring the pad surface. That balance matters on fine-pitch BGA pads, where a coarse hardware-store brush strips solder mask and lifts copper. Steel also cuts through hardened glue and oxidized tin that a soft bristle only smears. The bristles carry an anti-static design, which suits work around sensitive ICs. Mijing locks the bristles in place with professional equipment, so the clamping force holds after long use. The tight bristle layout also reaches motherboard cracks and narrow gaps between components. The colorful handle helps you pick this brush out from the other tools on your bench.
Steel Brush for Mobile Repair: Heat, Scrub, Inspect
Pair the brush with a heating platform and you clean the chip while the glue and tin stay soft. Mijing specifies a working range of -20°C to 550°C, and the bristles resist deformation at high temperature, so the brush head survives next to hot air and a preheating platform. A typical sequence on a boot loop issue or hang on logo fault looks like this: preheat the board, lift the IC with hot air, scrub the residue off the pad with the steel side, then sweep the dust away with the sideburns brush. Heat does the first half of the job and the brush does the second. If you scrub a cold board, you fight hardened glue and risk the pad edges, so warm the area first. Finish with flux and isopropyl alcohol, then check the pads under your microscope before you reball or reflow. Use light pressure and short strokes in one direction. The same routine works on charging issue and network issue boards that need an IC change karna.
What the 2in1 Set Includes and Where It Fits Your Bench
The package contains one IC pad steel brush and one sideburns brush, so you get a scrubbing tool and a sweeping tool in one purchase. Use the steel brush for glue residue, leftover tin, and solder residue on CPU and IC pads. Use the sideburns brush for dust and loose debris before you inspect or tin the pads. The set sits in the same workflow as Hot Air Stations, PCB Holders, Microscopes, and Reballing Kits, so it drops straight into a bench that already runs those tools. When the pads come out clean and flat, a BGA reballing kit gives you the natural next step. Replace the brush when the bristles bend or shed, because a worn head loses its cutting edge and leaves residue behind. The brush is universal and not device-specific, so one set covers boards from any phone brand, which suits repair shops and training institutes that handle mixed work.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Imported ultra-fine steel wire bristles at 0.08mm
- ✓Closely packed bristles, rigid yet flexible
- ✓Anti-static bristle design
- ✓Working range of -20°C to 550°C
- ✓Bristles resist deformation under heat
- ✓Bristles locked in place with consistent clamping force
- ✓2in1 set with steel brush and sideburns brush
- ✓Colorful handle for quick identification
Specifications
| Brand | Mijing |
|---|---|
| Model | SS2 (Phantom) |
| Category | IC Pad Cleaning Brushes |
| Compatibility | Mobile phone motherboards, CPU and IC solder pads (universal, not device-specific) |
| Technology | Ultra-fine 0.08mm steel wire bristles, anti-static bristle design |
| Material | Steel wire bristles |
| Operating Temperature | -20°C to 550°C |
| Package Contents | 1 x IC pad steel brush, 1 x IC pad sideburns brush |
Common Repair Uses
- ✓Removing glue residue from pads after IC change karna
- ✓Clearing leftover tin from CPU and IC pads
- ✓Polishing pads before reballing or reflow
- ✓Cleaning a chip while it sits on a heating platform
- ✓Sweeping dust off the board before microscope inspection
- ✓Cleaning solder residue after hot air rework
- ✓Cleaning motherboard cracks and tight gaps
- ✓Preparing pads on boot loop, hang on logo, and charging issue boards
Compatible Devices
- ✓Universal — not device-specific; works on IC and CPU pads of any phone motherboard
- ✓Mobile phone motherboards of any brand
- ✓CPU solder pads
- ✓BGA IC pads after chip removal
- ✓Chips heated on a preheating platform
- ✓Motherboard cracks and tight gaps between components
- ✓Chips with leftover glue residue
- ✓Chips with leftover tin
- ✓General PCB surfaces with dust or solder residue
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What temperature range can the Mijing SS2 steel brush handle?
Can I use the Mijing SS2 steel brush with a heating platform to remove glue after an IC change?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



