0.8mm Curved Nozzle for 2008 Series Hot Air Gun
₨ 1
Curved Nozzle for 2008 Hot Air Gun
This 0.8mm curved nozzle for 2008 hot air gun stations gives you a narrow, angled airflow for precise rework on mobile phone boards. The bent tip keeps the nozzle body out of your line of sight, so you can watch the component while you heat it. It fits the 2008 series hot air gun and suits connector work, small IC change karna jobs, and tight areas next to shields and neighbouring parts. If your bench runs a 2008 series station, this nozzle adds a focused tip for jobs where a wide airflow heats too much of the board. Mechanicpk supplies it to repair shops and technicians across Pakistan.
Out of stock
0.8mm Curved Nozzle for 2008 Series Hot Air Gun
A curved nozzle for 2008 hot air gun stations changes how you approach dense phone boards. The 2008 series handle fits a range of nozzle shapes, and this 0.8mm curved version suits technicians who need a narrow, angled stream instead of a wide, straight one. The bent geometry points the airflow at the component while the handle stays at a comfortable angle above the board. You see the part you work on, not the nozzle body. This page covers where the nozzle fits in your rework process, what the angled tip does for you, and which jobs justify keeping it in your nozzle set.
How the Curved Tip Helps on Dense Boards
Modern phone boards pack ICs, connectors, and shield frames close together. A straight nozzle often blocks your view and pushes heat across the neighbouring parts. The curved tip tackles both problems. The angled outlet lets you approach a component from the side, and the narrow opening concentrates airflow on a small target. You decide where the heat lands by tilting the handle rather than by moving the whole station. This matters most on charging port areas, battery connectors, and small ICs surrounded by tall components.
Where It Fits in Your Rework Workflow
Hot air rework sits in the middle of many repair jobs. A technician diagnoses a hardware fault, locates the failed part, lifts it with hot air, cleans the pads, and fits a new one. The 0.8mm curved nozzle covers the lifting and refitting steps on small components. It suits charging issue repairs where you replace a connector or a small IC, display problem repairs where you rework a flex connector area, and dead phone jobs where a small part on the power section needs changing. You still pair it with flux, tweezers, and a PCB holder, and you still choose the right nozzle size for the part in front of you. Keep wider nozzles from your 2008 range for larger ICs and use this one when precision matters more than coverage.
Compatibility with the 2008 Series
This nozzle fits the 2008 series hot air gun. Station-specific nozzles are not interchangeable across series, so confirm that your handle belongs to the 2008 family before you order. A nozzle made for the 861 series will not suit this handle, and the reverse also applies. Matching the nozzle to the station protects airflow consistency and keeps the fit secure during a repair.
Why Technicians Keep It in the Nozzle Set
Experienced technicians rarely work with one nozzle. They rotate between sizes and shapes depending on the part, the space around it, and how much of the board they want to heat. A narrow curved nozzle earns its place because it handles jobs that wider nozzles handle poorly. It costs little compared with the station itself and extends what your 2008 series gun can do. Repair shops that handle a steady flow of charging port and connector jobs notice the difference in speed and control. Add it to your bench alongside soldering stations, PCB holders, and a good microscope, and your rework area covers more of the repairs customers bring through the door. Order from Mechanicpk and pick up the rest of your hot air station accessories in the same checkout.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Curved tip that directs airflow at an angle
- ✓Keeps the nozzle body out of your line of sight
- ✓Narrow 0.8mm opening for concentrated heat
- ✓Built for the 2008 series hot air gun
- ✓Suits precision work around tall neighbouring components
- ✓Fits into a multi-nozzle workflow with wider 2008 nozzles
- ✓Useful for charging issue and connector repairs
- ✓Supports small-area rework without heating the wider board
Specifications
| Model | 0.8mm Curved Nozzle |
|---|---|
| Category | Hot Air Gun Nozzles |
| Compatibility | 2008 Series Hot Air Gun |
| Technology | Hot air rework |
| Nozzle Size | 0.8mm |
| Nozzle Shape | Curved / angled |
Common Repair Uses
- ✓Hot air rework on small components and tight board areas.
- ✓Charging connector replacement
- ✓Small IC removal and refitting
- ✓Battery connector rework
- ✓Flex connector area rework on display problem repairs
- ✓Shield frame and neighbouring part heating control
- ✓Component lifting on dead phone boards
- ✓Jumper lagana preparation, where you clear pads before bridging
- ✓Small part reflow on boards with limited space
Compatible Devices
- ✓Fits the 2008 series hot air gun handle. It is not phone-model-specific, so it works on boards from any brand that you rework with hot air.
- ✓Samsung phone boards
- ✓Oppo phone boards
- ✓Vivo phone boards
- ✓Infinix phone boards
- ✓Tecno phone boards
- ✓Xiaomi phone boards
- ✓Realme phone boards
- ✓iPhone logic boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Will this nozzle fit an 861 series hot air gun?
When should I use a curved nozzle instead of a straight nozzle?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



