2UUL FX-002 0.02mm Ultrafine Jumper Wire 100m

₨ 800

0.02mm Ultrafine Jumper Wire

The 2UUL FX-002 ultrafine jumper wire for mobile repair gives your micro-soldering bench a 0.02mm non-insulated conductor on a 100-metre length. You cut the exact length you need and bridge a lifted pad, a burnt trace, or a broken connection between IC pads. The wire stays thin enough to route between tight BGA contacts on smartphone motherboards. The manufacturer rates it as non-magnetic with good toughness and no breakpoints, so it holds its shape under a microscope while you position and solder it. One spool covers hundreds of jumper repairs across dead phone, charging issue, and fingerprint circuit jobs.

In stock

19 People watching this product now!
Description

Ultrafine Jumper Wire for Mobile Repair: 2UUL FX-002 Overview

The 2UUL FX-002 is an ultrafine jumper wire for mobile repair that measures 0.02mm in diameter and arrives on a 100-metre length. It solves one specific board-level problem: a pad, trace, or solder joint has lifted or burnt away and the circuit no longer completes. You cut a short strand, lay it across the damaged path, and solder both ends. That restores continuity on a dead phone or hardware fault without replacing the board. The FX-002 uses a non-insulated conductor, so the bare wire takes solder directly at each contact point.

Why 0.02mm Matters on Dense Smartphone Boards

Pad spacing on modern phone CPUs, PMICs, and sensor connectors leaves almost no room for a thick jumper. At 0.02mm, the FX-002 runs between closely spaced BGA pads and IC pad rows without touching the neighbouring contact. The manufacturer lists the wire as non-magnetic, tough, and free of breakpoints. That combination matters when you handle a strand under a microscope, because a wire that kinks or springs away costs you time on every joint. You straighten the strand, tack one end with your soldering station, route the wire along the damaged path, and finish the second end. Keep your soldering iron temperature controlled and your flux fresh, since a wire this fine reacts quickly to excess heat.

Where the FX-002 Fits in Your Repair Workflow

Start with diagnosis. Use your multimeter in continuity mode to confirm which pad or trace has broken, then clean the area and expose the damaged pad. Secure the board in a PCB holder and work under a microscope. After you place the FX-002 jumper, test continuity again before you reassemble anything. Technicians use this wire for IC chip pad repair, bridging components and IC chips, CPU solder joint peeling repair, and fingerprint circuit repair. When a repair also needs a BGA chip lifted and reseated, pair the jumper step with your hot air station and reballing kit so the chip sits on clean, tinned pads before you add the wire.

Choosing Between the FX-002 and Other 2UUL Wire Variants

2UUL sells this wire family in several versions, and the right pick depends on the board. The FX-002 gives you 0.02mm of non-insulated conductor, which suits most pad and trace repairs where the wire runs a short, clear path. The FX-002A offers the same 0.02mm diameter with insulation, which helps when your route crosses another trace. When pads shrink further, the FX-001 at 0.01mm and the FX-009 at 0.009mm offer finer options, so you can step up as your micro-soldering skill grows. Mechanicpk stocks the FX-002 as the practical middle size for workshops that handle daily Samsung, Xiaomi, Huawei, and iPhone motherboard jobs and want one dependable jumper wire on the bench.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.02mm ultrafine conductor diameter
  • 100-metre spool length for high-volume use
  • Non-insulated wire that takes solder directly
  • Non-magnetic wire for clean handling under magnification
  • Good toughness with no breakpoints, as listed by the manufacturer
  • Fits IC pad, trace, and BGA joint repair
  • Universal use across phone brands and PCB types
  • Sits in the 2UUL range between the finer FX-001/FX-009 and the insulated FX-002A

Specifications

Brand2UUL
ModelFX-002
CategoryJumper Wire / Micro-Soldering Consumables
CompatibilityUniversal, not device-specific
TechnologyUltrafine non-insulated conductive jumper wire
Wire Diameter0.02mm
Length100m

Common Repair Uses

  • Board-level jumper and pad repair on mobile phone and electronic motherboards
  • IC chip pad repair
  • Bridging components and IC chips
  • Damaged PCB trace repair
  • CPU solder joint peeling repair
  • BGA chip pad repair
  • Fingerprint circuit repair
  • Motherboard micro-soldering
  • Flying-wire connection for lifted pads

Compatible Devices

  • Universal micro-soldering wire for mobile phone and electronic motherboards, not limited to specific models
  • Samsung smartphone motherboards
  • Apple iPhone motherboards
  • Huawei smartphone motherboards
  • Xiaomi smartphone motherboards
  • Google Pixel motherboards
  • Smartphone CPU BGA pads
  • Fingerprint sensor circuit pads
  • General electronic PCBs

FAQ

What is the product name?
The product name is 2UUL FX-002 0.02mm Ultrafine Jumper Wire 100m.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is FX-002.
What is this product used for?
This product is used for repairing damaged pads and traces, bridging components and IC chips, and restoring broken connections on mobile phone motherboards.
Which devices are compatible with this product?
This product is compatible with mobile phone and electronic motherboards as a universal micro-soldering wire, including Samsung, Apple, Huawei, Xiaomi, and Google boards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the difference between the 2UUL FX-002 and FX-002A jumper wire?
Both wires measure 0.02mm. The FX-002 has no insulation, while the FX-002A carries insulation, which helps when the wire crosses another trace.
Can the FX-002 jumper wire repair CPU BGA pads on a mobile motherboard?
Yes. Technicians use this 0.02mm wire for CPU and BGA chip pad repair and solder joint peeling repair, bridging the damaged pad to the next connection point.