Mijing AR-2020 Alpha Solder Wick 2mm x 2m (5pcs/box)

₨ 1,499

Mijing AR-2020 Desoldering Braid

The Mijing AR-2020 Alpha solder wick gives your bench a 2.0 mm wide, 2 m long copper braid for lifting molten solder off mobile motherboard pads. The fluorine-free flux formula leaves little residue, and the anti-oxidation treatment keeps the braid ready to wet on contact with your iron tip. The soft weave bends into tight spaces around BGA footprints and connector pads, so you clean the pad without lifting tracks. Mechanicpk supplies the AR-2020 as a 5-piece box, which suits repair shops that run several rework jobs a day and want a fresh length for every board.

In stock

10 People watching this product now!
Description

Mijing AR-2020 Solder Wick for Mobile Board Rework

The Mijing AR-2020 solder wick gives your bench a 2 m roll of 2.0 mm copper braid that pulls molten solder off motherboard pads, IC footprints and connector lands. Mechanicpk supplies it as a 5-piece box, so every technician in your workshop starts a rework job with a fresh length instead of dragging a spent, solder-loaded tail across a clean pad. The Alpha series pairs a fluorine-free flux formula with an anti-oxidation treatment, which keeps the braid ready to wet the moment your iron touches it.

Technical Profile of the AR-2020 Braid

Mijing builds the AR-2020 from high-purity copper wire woven into a flat, flexible braid. Each piece measures 2.0 mm wide and 2.0 m long. The AR-2015 in the same Alpha range uses the same 2.0 mm width but ships at 1.5 m, so the AR-2020 gives you roughly a third more usable length per piece. The braid acts as a capillary channel: when you press heated wick against a solder joint, molten solder flows into the weave instead of staying on the pad. The flux inside the braid lowers surface tension and helps that flow start faster. Mijing formulates this flux without fluorine, which cuts the residue you scrub off afterward.

The weave stays soft. You can curve it around a shield frame edge or lay it flat across a row of pads without it springing back or fraying into loose strands that could bridge a footprint.

Where It Sits in Your Rework Workflow

After your hot air station lifts an eMMC, UFS, CPU or power IC, the pads underneath still carry uneven solder peaks. Lay the AR-2020 across the pads, press it down with your soldering iron tip, and drag it slowly toward fresh braid. The solder wicks up and leaves flat, bright pads that are ready for reballing or a new IC. Technicians doing IC change karna jobs use this step on every board, because a flat pad decides whether a stencil sits level and whether the new chip seats without bridges.

You also reach for it in smaller jobs. Clean the leftover solder from ISP wire points after a dead after flash recovery, tidy a jumper lagana point, or lift excess solder from a damaged charging port pad when you chase a charging issue. A microscope and a PCB holder make the work faster and steadier, and a multimeter lets you confirm no neighboring pads bridged after you finish cleaning.

Buying a 5-Piece Box for Workshop Use

Wick is a consumable. Each section of braid holds only so much solder before it stops absorbing, and you snip off the loaded portion and continue with fresh braid. A 5-piece box means each piece lasts through a stretch of board work, and you never reach for a half-used roll with oxidized strands. If you run a service center with multiple bench stations, one box covers a shift of desoldering braid for mobile repair in Pakistan without you re-ordering mid-week.

Pair the AR-2020 with a temperature-controlled soldering station, a hot air station and a reballing kit from the same Mechanicpk soldering category, and your pad-prep workflow stays complete from IC removal to the finished board.

Additional information
Weight0.5 kg
Q & A
Please login to post questions

Key Features

  • High-purity copper braid for fast solder absorption
  • 2.0 mm width suits BGA pads, connector lands and shield frame edges
  • 2.0 m length per piece, longer than the AR-2015’s 1.5 m
  • Fluorine-free flux formula with low residue
  • No-clean flux style for quick board turnaround
  • Anti-oxidation treatment keeps the braid ready to wet
  • Soft weave bends into tight spaces without fraying
  • 5-piece box covers multiple jobs and bench stations

Specifications

BrandMijing
ModelAR-2020 Alpha
CategoryDesoldering Wick / Solder Wick
CompatibilityUniversal — not device-specific
TechnologyFluorine-free flux, anti-oxidation treatment
MaterialHigh-purity copper braid
DimensionsWidth 2.0 mm, Length 2.0 m (per piece)
Package Quantity5 pieces per box

Common Repair Uses

  • Solder removal and pad cleaning on mobile boards
  • Cleaning BGA pads after eMMC, UFS or CPU removal
  • Flattening pads before reballing
  • IC change karna prep on power and charging ICs
  • Lifting excess solder from charging port pads
  • Clearing solder bridges between fine-pitch pads
  • Cleaning ISP and test point wire pads after flashing
  • Removing leftover solder from connector footprints
  • Tidying jumper points after a hardware fault repair

Compatible Devices

  • Universal — works on any board with solder joints, not tied to specific phone models
  • Android smartphone motherboards (all brands)
  • iPhone logic boards
  • Tablet motherboards
  • BGA pads after eMMC, UFS or CPU removal
  • Power IC and charging IC footprints
  • Charging port and connector pads
  • FPC and display connector pads
  • Small electronics and daughterboards

FAQ

What is the product name?
The product name is Mijing AR-2020 Alpha Solder Wick (5pcs/box).
What is the brand of this product?
The brand of this product is Mijing.
What is the model of this product?
The model of this product is AR-2020 Alpha.
What is this product used for?
This product is used for removing molten solder from PCB pads and cleaning IC footprints during mobile board repair.
Which devices are compatible with this product?
This product is universal. It works on any board with solder joints and does not depend on a specific phone model or chipset.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the size of the Mijing AR-2020 solder wick, and how does it differ from the AR-2015?
Each AR-2020 piece is 2.0 mm wide and 2.0 m long. The AR-2015 has the same 2.0 mm width but a shorter 1.5 m length.
Can I use the AR-2020 to clean BGA pads after removing an eMMC or CPU?
Yes. Lay the braid over the pads, press it with a heated soldering iron tip, and drag it away as the solder absorbs. Clean the board with flux cleaner afterward and check the pads under a microscope before reballing.