2UUL FX-002A 0.02mm Insulated Jumper Wire 100m

₨ 800

Insulated Jumper Wire for Phone PCB Repair

The 2UUL FX-002A insulated jumper wire for mobile repair gives you a 0.02mm conductor on a 100m spool, built for the fine trace and pad repairs that dead phone boards demand. The insulating layer keeps neighboring traces and BGA pads from shorting when you route a jumper across a crowded board. You tin it directly, solder it without breakpoints, and use it on phone, iPad and tablet motherboards, CPU BGA joints and fingerprint circuits. One spool keeps your bench stocked for a long run of jumper lagana jobs.

In stock

19 People watching this product now!
Description

2UUL FX-002A: Insulated 0.02mm Jumper Wire for Board-Level Repair

The 2UUL FX-002A is an insulated jumper wire for mobile repair that measures 0.02mm across and ships as a 100m spool. Board-level technicians reach for it when a lifted pad, a damaged trace or a peeled BGA joint leaves a dead phone with no copper path back to the CPU. The insulation separates this model from the bare 0.02mm FX-002 in the same 2UUL range, so you can lay the wire across a dense area without covering every neighboring pad first. If your bench handles hardware fault jobs every day, this spool gives you one consistent, repeatable jumper material.

Why Insulation Matters at 0.02mm

At this diameter, a bare wire touches more than you intend. Pad pitch around a CPU BGA package leaves almost no clearance, and one stray strand turns a trace repair into a new short circuit. The FX-002A carries an insulating layer, so a jumper can cross adjacent traces and test points while you route it to the destination pad. Keep a microscope on the bench to place each end accurately, and confirm continuity with a multimeter before you close the phone.

The wire is non-magnetic and tough enough to straighten and route without snapping. Its no-breakpoint construction lets you solder one continuous run instead of building an extension joint halfway across the board. Low solder resistance and easy tinning mean the wire accepts solder quickly, and the product specification lists no paint scraping before soldering.

Where It Fits in Your Repair Workflow

Use the wire after you diagnose the break. Inspect the board under magnification, clean the damaged area, then expose the pad you need to reconnect. Tin the wire end, flow it onto the pad with a hot air station or a fine soldering station tip, route it along the shortest safe path, and solder the far end to the next live point. Hold the board steady in a PCB holder so your hands stay free for the final placement.

Technicians in Pakistan use this method for jumper lagana on CPU BGA connections, fingerprint circuits and lifted pads, including repairs that follow an IC change karna job on iPhone, iPad, Android and tablet boards. It also helps with charging issue and display problem faults where a trace has burned or a pad has torn away. Because the wire is so fine, control your soldering temperature and keep the tip clean so you do not overheat the surrounding pads.

Choosing FX-002A From the 2UUL Range

The 2UUL jumper wire range includes 0.009mm, 0.01mm and 0.02mm non-insulated options, plus the FX-002S ultrasoft 0.02mm version. The FX-002A keeps the 0.02mm diameter and adds insulation. Choose it when the repair path crosses other conductors. Choose the non-insulated FX-002 when the route is clear and you want a bare conductor.

A 100m spool gives a repair shop or service center enough stock for continuous board-level work, and it sits naturally beside reballing kits, PCB holders, test boxes and multimeters on a well-equipped bench. Shops that also run ISP pinout tools, eMMC programmers and UFS adapters for dead after flash jobs cover the full cycle, because a hardware repair often ends with a software check.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • 0.02mm ultra-fine conductor diameter
  • Insulated construction for crossing neighboring traces
  • 100m spool length
  • No-breakpoint construction for direct soldering
  • Non-magnetic wire
  • Good toughness for routing and straightening
  • Low solder resistance and easy tinning
  • No paint scraping required before soldering

Specifications

Brand2UUL
ModelFX-002A
CategoryJumper Wire / Soldering Accessories
CompatibilityUniversal, not device-specific
Supported DevicesMobile phone, iPad, tablet and other electronic motherboards with CPU BGA chips
TechnologyInsulated ultra-fine jumper wire, 0.02mm diameter
Dimensions0.02mm wire diameter, 100m length

Common Repair Uses

  • Fine jumper repair on phone and tablet PCBs
  • CPU BGA solder joint peeling repair
  • Fingerprint circuit repair
  • Lifted pad reconnection
  • Broken trace bridging
  • Motherboard jumper wiring
  • Phone PCB micro-soldering
  • iPad and tablet board repair
  • Routing a jumper across neighboring traces without shorting

Compatible Devices

  • Universal ultra-fine jumper wire for phone, iPad, tablet and electronic motherboard repair, not limited to specific models
  • Apple iPhone motherboards
  • Apple iPad motherboards
  • Samsung phone motherboards
  • Huawei phone motherboards
  • Xiaomi phone motherboards
  • Google phone motherboards
  • Android and other tablet motherboards
  • Other electronic motherboards with CPU BGA chips

FAQ

What is the product name?
The product name is 2UUL FX-002A Insulated Jumper Wire.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is FX-002A.
What is this product used for?
This product is used for jumper repairs on phone, iPad and tablet motherboards, including CPU BGA joint, fingerprint circuit and broken trace repair.
Which devices are compatible with this product?
This product is universal and not device-specific. It suits phone, iPad, tablet and electronic motherboard repair, including iPhone, Samsung, Huawei, Xiaomi and Google devices.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the difference between 2UUL FX-002 and FX-002A jumper wire?
Both are 0.02mm wires on a 100m spool. The FX-002 is non-insulated, and the FX-002A is insulated, so the FX-002A suits repairs where the wire crosses other traces or pads.
Do I need to scrape the coating before soldering the FX-002A?
The product specification lists easy tinning with no paint scraping, so you tin the wire end directly and solder it to the pad.