WYLIE CPU IC Pry Knife Set Hand Finish Blades

₨ 1

WYLIE Hand Finish Pry Knife Set

The WYLIE hand finish blades give your bench a dedicated CPU IC pry knife set for board-level chip work. Thin, hand-finished blades slide under CPU, NAND and other BGA packages once heat softens the solder and glue. They also cut and scrape the epoxy that surrounds a chip. You lift the package cleanly and leave your pads ready for reballing. Mobile repair shops use this set during IC change karna jobs, dead phone diagnosis and hardware fault repairs. Mechanicpk supplies it to Pakistani technicians who need predictable chip separation without damaging the motherboard.

Out of stock

12 People watching this product now!
Description

CPU IC Pry Knife Set for Board-Level Chip Separation

A CPU IC pry knife set earns its place on your bench at the moment a heated chip needs to lift without taking its pads along. The WYLIE hand finish blades give you thin working edges that reach under CPU, NAND and similar BGA packages and cut through the glue around them. Screwdrivers and general-purpose scalpels flex, slip and gouge the solder mask. A purpose-made blade profile controls the lift and protects the board.

Where the Blades Fit in the Chip Removal Sequence

Chip removal follows a fixed order: preheat, apply hot air at the correct profile, separate the package, then clean the pads. These blades cover the separation and cleaning stages. Your Hot Air Station brings the package to reflow temperature and softens the surrounding epoxy. Then you slide the blade edge under the chip and lift. Cold prying tears pads, so the thermal profile behind the blade decides the result. Mount the motherboard in a PCB Holder first so the board stays flat and your hand stays steady while you work the edge in.

Glue Removal Around CPU and Flash Packages

Corner glue and black underfill hold many CPU, NAND and baseband packages firmly to the board. The blade edge cuts that glue along the package perimeter before you apply any lift, which reduces the force the chip sees. After the chip comes off, you scrape the residue from the pads and the surrounding area. Clean lands make reballing faster and produce more reliable joints. Pair the set with Reballing Kits and a Microscope so you can check every pad before you place the next chip.

Handling Dead Phone and Hardware Fault Jobs

Many dead phone cases, boot loop issues and dead after flash faults end with a memory or processor replacement at board level. In those jobs, a damaged pad turns a repairable board into a scrap board. A precise blade lowers that risk. You can use the same set when you separate stacked boards, remove edge adhesive or clear sealant around shields and connectors. After the chip comes off, test pad continuity with your Multimeter. Finish pad cleaning with a temperature-controlled Soldering Station before you fit the replacement.

Building Your Bench Around the Blade Set

A blade set works best inside a complete rework setup. Start with this set, a Hot Air Station and a PCB Holder, which covers the core of chip-off work. Then move up to a Microscope for inspection and Reballing Kits for rebuilding the chip. When you can avoid chip-off, ISP Pinout Tools, eMMC Programmers and UFS Adapters let you read or write flash data without lifting the package. Test Boxes and the blade set then cover the jobs that need the chip off the board. This sequence matches how Pakistani repair shops expand their tool inventory as their workload grows.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Hand-finished thin blades for working under chip edges
  • Designed for CPU, NAND and IC prying
  • Cuts and scrapes underfill and edge glue
  • Slim profile reaches tight gaps around packages
  • Controlled lift reduces pad damage when you apply correct heat
  • Suits chip-off preparation before reballing
  • Works with hot air station and PCB holder setups
  • Suits technicians, repair shops and service centers

Specifications

BrandWYLIE
CategoryMobile Repair Tools – Pry Knives and Blades
CompatibilityUniversal – not device-specific

Common Repair Uses

  • Board-level chip separation, glue removal and pad cleaning on mobile phone boards
  • CPU removal after hot air heating
  • NAND, eMMC and UFS chip lifting for replacement
  • Black glue and underfill cutting around packages
  • Corner and edge glue removal
  • Pad cleaning before reballing
  • IC change karna on boards with glued chips
  • Hardware fault repair on dead phone boards
  • Separating glued board layers

Compatible Devices

  • Universal – not device-specific; used on mobile phone and tablet motherboards where chips sit under glue
  • Mobile phone motherboards with glued CPU packages
  • NAND flash chips bonded with edge glue
  • BGA memory and processor packages on phone boards
  • eMMC and UFS chips on boards that need chip-off
  • Baseband and other IC packages with corner glue
  • Tablet motherboards with underfilled chips
  • Stacked or glued board layers during disassembly
  • Boards prepared for reballing after chip removal

FAQ

What is the product name?
The product name is WYLIE Hand Finish Blades Glue Removal CPU IC Pry Knife Set.
What is the brand of this product?
The brand of this product is WYLIE.
What is this product used for?
This product is used for prying CPU and IC chips, cutting underfill and removing edge glue on mobile phone motherboards.
Which devices are compatible with this product?
This product is universal and not device-specific. You use it on mobile phone and tablet boards that have glued CPU, NAND or IC packages.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Do I need to heat the board before I use these blades?
Yes. Heat the chip and the surrounding glue with a hot air station until the solder and epoxy soften. Prying a cold chip rips pads off the board.
Can I use this knife set to lift NAND or eMMC chips on a dead phone?
Yes. After heating, you can slide the blade under a NAND or eMMC package to separate it. Check the pads under a microscope before you reball or fit a replacement.
Does a blade set replace ISP or eMMC programmer methods?
No. ISP and programmer methods read or write flash data without lifting the chip. You use the blade set when the chip must come off the board for replacement or reballing.