Mechanic iSm5 138℃ Specific Paste For Jumper Wire
₨ 1
Jumper Wire Solder Paste for Mobile Repair
Mechanic iSm5 138℃ Specific Paste For Jumper Wire gives your bench a purpose-built jumper wire solder paste for mobile repair. The 3 ml pack ships with 3 application needles, so you place a small, controlled amount on the pad instead of flooding the joint. Its nano-compound formula delivers high activity with moderate viscosity, and the iron tip tins a point with a single stamp. Use it for fly line repairs on broken pads and tracks, iPhone fingerprint line repair, and BGA-area rework on phone and laptop motherboards. Mechanicpk supplies it to technicians, repair shops and service centers across Pakistan.
Out of stock
Mechanic iSm5 Jumper Wire Solder Paste for Precision Board Repair
Mechanic iSm5 138℃ Specific Paste For Jumper Wire is a jumper wire solder paste for mobile repair that does one job well: tinning tiny pads and fly line points so a jumper wire holds cleanly on a damaged board. Mechanic supplies it as a 3 ml paste with 3 application needles, and the nano-compound formula combines high activity with moderate viscosity. When a dead phone traces back to a broken track, a lifted pad or a cut fingerprint line, this paste sits at the center of the repair. You pick up a small amount, set it on the solder spot, and your iron finishes the joint.
How the Nano-Compound Formula Behaves on Your Bench
The iSm5 formula uses industrial-grade nano compounds, and that gives the paste its high activity. High activity means the paste wets a pad fast, so you need very little of it per point. Wipe your iron tip between points, because a clean tip transfers a fresh, bright layer on every stamp. Moderate viscosity means you can pick up a small dot on the needle tip and place it exactly where the wire needs to land. Once the paste sits on the spot, the iron head tins it with a single stamp, which leaves a full tin point ready for the jumper wire. Pair it with a temperature-controlled soldering station and a stereo microscope, and you control every joint on a board where pads measure fractions of a millimeter.
Using Jumper Wire Solder Paste for Mobile Repair on Real Faults
Most jumper jobs start with a hardware fault, not a software one. A charging issue often leads you to a burnt or cut track near the charging IC. A display problem can trace to a broken line on the connector side. A fingerprint sensor that stops responding after a drop points to a damaged flex line. In each case your workflow follows the same order: confirm the open line with a multimeter, expose the track under the microscope, tin the pad with iSm5, lay the fly line wire, and tin the far end. A PCB holder keeps the board still while you work, and a hot air station handles any nearby components that need to come off first.
The same paste supports deeper board work. When you rebuild pads under a BGA chip or recover a damaged pad during reballing, a clean tinned point gives the jumper wire a solid anchor. Technicians who run ISP pinout tools, eMMC programmers or UFS adapters also reach for jumper wire when a test pad has lifted and the programmer cannot reach it directly. A test box confirms the result once the repair is complete, so you verify the fix before the phone leaves your bench and avoid a repeat visit from the customer.
Why Repair Shops Stock Mechanic iSm5
Jumper paste is a consumable, so you reorder it often, and a 3 ml pack with its own needles keeps one unit at every bench instead of sharing a single tube across the shop. The needles let junior technicians dose the paste the same way every time, which cuts waste and keeps joints uniform from one repair to the next, even when several technicians share the same workload. Mechanic positions the iSm5 for mobile phone repair, laptop repair and motherboard BGA welding, so one pack covers the common board-level jobs a Pakistani repair shop sees each week.
Mechanicpk stocks Mechanic iSm5 alongside soldering stations, hot air stations, microscopes, multimeters, PCB holders and reballing kits, so you can build a complete jumper wire setup in one order. Start with the paste and needles, add a fine jumper wire and a good microscope, and your board-level repairs get cleaner with every point you tin.
| Weight | 0.5 kg |
|---|
Key Features
- ✓3 ml paste pack
- ✓3 application needles included
- ✓Nano-compound formula with high activity
- ✓Moderate viscosity for controlled placement
- ✓Single-stamp tinning with the iron head
- ✓Full tin point for fly line attachment
- ✓Made specifically for jumper wire repair
- ✓Suits mobile phone, laptop and BGA-area board repair
Specifications
| Brand | Mechanic |
|---|---|
| Model | iSm5 (3 ml paste with 3 application needles) |
| Category | Jumper Wire Solder Paste / Soldering Consumables |
| Compatibility | Mobile phone PCBs, laptop motherboards, motherboard CPU and BGA chip repair (universal, not device-specific) |
| Technology | Nano-compound formula, high activity, moderate viscosity |
Common Repair Uses
- ✓Jumper wire and fly line soldering on damaged boards
- ✓Fly line jumper wire soldering on mobile phone PCBs
- ✓Repairing broken pads and cut tracks
- ✓iPhone fingerprint line repair
- ✓Charging line repair after a cut or burnt track
- ✓Display connector line repair
- ✓Pad recovery during BGA reballing
- ✓Tinning pads before laying jumper wire
- ✓Laptop motherboard track repair
Compatible Devices
- ✓Universal board-level use, not tied to specific phone models
- ✓Mobile phone motherboards (all brands, jumper wire and fly line repair)
- ✓iPhone fingerprint line repair
- ✓Broken pads and tracks on phone PCBs
- ✓Laptop motherboards
- ✓Motherboard CPU repair areas
- ✓BGA chip areas on phone and laptop boards
- ✓Fine-gauge jumper wire and fly line work
- ✓Soldering iron tip tinning at the solder point
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How much paste and how many needles come in the Mechanic iSm5 pack?
How do I apply Mechanic iSm5 paste to tin a jumper wire point?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



