Back to products
Relife RL-001G Tool Box
Relife RL-001G Tool Box for Mobile Repair Storage Original price was: ₨ 2,000.Current price is: ₨ 1,800.

Relife F-22 Metal Flux Paste for Mobile Repair

₨ 1

Relife F-22 Metal Soldering Flux

Relife F-22 metal flux paste gives your bench a dedicated flux for stainless steel, nickel sheet, copper, iron and galvanized metal. The halogen-free translucent paste strips oxide films while you solder and improves how solder wets the metal. It ships in a syringe with a push rod, so you dispense exact amounts and waste nothing. Technicians use it for oxidised pads, shield and connector metal, and jumper points on boards that arrive as a dead phone or hardware fault. Mechanicpk supplies the Relife F-22 to repair shops and service centers across Pakistan that want a reliable metal-surface flux next to their soldering station and hot air station.

Out of stock

12 People watching this product now!
Description

Relife F-22 Metal Flux Paste for Hard-to-Wet Metal Surfaces

The Relife F-22 metal flux paste targets a problem every board-level technician meets sooner or later: solder that refuses to wet stainless steel, nickel sheet or an oxidised copper pad. Relife formulates this halogen-free translucent paste to remove oxide films during soldering and to improve metal adhesion. Your iron tip or hot air nozzle then works on a clean metal surface instead of fighting a dull, oxidised one. Mechanicpk stocks the F-22 for Pakistani repair shops that want a metal-specific flux beside their general-purpose BGA flux. The syringe format keeps application controlled on a busy bench.

Material Scope and Technical Profile

Most phone-repair fluxes target copper pads and tinned joints. The F-22 widens that scope. The manufacturer lists it for stainless steel, nickel sheet, copper, iron and galvanized sheet, and for repairing oxidation spots. That range covers the metal you meet during board-level work: shield cans, battery connector tabs, charging port shells and jumper anchor points.

The paste is halogen-free and non-corrosive, and it carries no irritating odour. You notice that difference when you solder for hours at a stretch. Supplier data also describes it as non-conductive with high insulation resistance, so leftover residue does not open a leakage path between fine traces. The translucent body lets you watch the joint form as the solder flows.

Where the F-22 Fits in Your Repair Workflow

Picture a dead phone that traces back to an oxidised jumper point or a lifted metal shield. You clean the area, lay a thin line of F-22 from the syringe, and tin the metal with your soldering station. For larger metal parts, a hot air station spreads the heat evenly while the flux keeps the surface active. A PCB holder keeps the board steady during jumper lagana, and a microscope lets you confirm that the solder wetted the whole joint instead of beading on top.

After soldering, a multimeter check confirms continuity across the repaired point before you reassemble. The F-22 supports the metal-side work around an IC change karna job. For the chip itself, many technicians still reach for their dedicated BGA flux and reballing kit. That split keeps each flux on the job it handles best and gives you predictable results on charging issue and display problem boards alike.

Syringe Handling for Clean, Repeatable Application

The syringe design ships with a push rod and needles in different sizes, so you pick the tip that matches the joint. Fine needles suit tight jumper points. Wider needles suit shield edges and connector tabs. You push out a small bead, spread it with the tip, and heat the joint. Because the paste stays where you place it, you avoid the flooding that wastes flux and spreads residue across nearby components.

Store the syringe capped and upright, and wipe the needle after each use so the paste does not dry in the tip. Shops that run several benches usually keep one syringe per technician, which stops cross-contamination between fluxes and keeps the paste fresh.

Why Distributors Stock It for Repair Shops

Metal-surface soldering shows up daily in a Pakistani repair market where charging port shells, battery connectors and shield cans take constant abuse. A single-purpose flux for that work cuts rework and shortens each repair. The F-22 gives your team a low-odour, non-corrosive option at a bench-friendly syringe size, and it slots straight into the soldering consumables you already buy alongside soldering stations, hot air stations, reballing kits and microscopes.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • Halogen-free translucent paste formula
  • Removes oxide films during soldering
  • Improves metal adhesion and solder wetting
  • Works on stainless steel, nickel, copper, iron and galvanized sheet
  • Non-corrosive with no irritating odour
  • Non-conductive with high insulation resistance
  • Syringe design with push rod and needles of different sizes
  • Controlled dispensing with minimal waste

Specifications

BrandRelife
ModelF-22
CategorySoldering Flux
CompatibilityStainless steel, nickel sheet, copper, iron and galvanized sheet metals
TechnologyHalogen-free translucent paste flux, non-corrosive, non-conductive with high insulation resistance

Common Repair Uses

  • Metal soldering and oxide removal in mobile and PCB repair
  • Repairing oxidation spots on metal surfaces
  • Soldering stainless steel and nickel sheet parts
  • Tinning copper pads before soldering
  • Jumper wire soldering on dead phone boards
  • Re-soldering metal shield edges
  • Connector and charging port shell soldering
  • Iron and galvanized metal joining
  • General PCB and electronics soldering repair

Compatible Devices

  • Universal metal-soldering flux, not tied to specific phone models, brands or chipsets
  • Stainless steel parts
  • Nickel sheet parts
  • Copper pads and traces
  • Iron metal parts
  • Galvanized sheet metal
  • Oxidised metal spots
  • General electronics and PCB soldering work
  • Any phone brand, since the flux works on the metal rather than the device model

FAQ

What is the product name?
The product name is Relife F-22 Metal Special Flux Paste.
What is the brand of this product?
The brand of this product is Relife.
What is the model of this product?
The model of this product is F-22.
What is this product used for?
This product is used for soldering metal surfaces and repairing oxidation spots during mobile and PCB repair.
Which devices are compatible with this product?
This product is a universal metal-soldering flux. It works on stainless steel, nickel sheet, copper, iron and galvanized sheet, and it does not depend on a specific phone model or chipset.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which metals can Relife F-22 flux paste solder?
Relife lists the F-22 for stainless steel, nickel sheet, copper, iron and galvanized sheet, and for repairing oxidation spots on these metals.
Is Relife F-22 flux safe to use on a PCB, and will its residue conduct?
The paste is halogen-free and non-corrosive. Supplier data describes it as non-conductive with high insulation resistance, so leftover residue does not form a conductive path between traces.