Mechanic 900M-T-C6 Heating Platform for T12 & JBC Tips
₨ 500
Mini Copper Heating Plate for Iron Tips
The Mechanic 900M-T-C6 heating platform adds a pure copper honeycomb work surface to the soldering station you already run. It fits T12, JBC C210/C245 and 936 / 900M-T style tips, and spreads heat evenly under flex cables, connectors and small PCB sections. Use it for Face ID flex repair, board-to-board connector swaps and bottom-heating before micro soldering, where hot air would damage nearby plastic. The package contains the plate only, so match it with a compatible tip and station. For whole motherboards, pair it with a full-size preheater or hot air station.
Out of stock
900M-T-C6 Heating Platform: Copper Rework Plate for Iron Tips
The 900M-T-C6 heating platform from Mechanic turns the soldering iron on your bench into a compact bottom-heat rework surface. A 99.99% pure copper plate with a hexagonal honeycomb face mounts on a compatible iron tip and spreads the iron’s heat across a small, even zone. You warm a flex cable, connector or sub-board uniformly instead of pointing hot air at it. The plate covers the gap between a bare iron tip and a full preheater: FPC repairs, Face ID flex work, connector swaps and small IC rework on boards where nearby plastic cannot survive a hot air nozzle.
How the Honeycomb Copper Plate Works
Mechanic builds the plate from 99.99% pure copper, and copper pulls heat from the iron tip into the work surface quickly. The honeycomb structure gathers that heat across the top face, so you get one consistent hot zone instead of a single contact point. Consistency matters when you reflow a ribbon-style flex cable: a cold edge lifts and a hot edge scorches. You set your station temperature the way you always do for the job, place the part on the plate and let the copper spread the heat. The plate extends your iron’s heating element and does not replace it, so your station’s controller still governs the temperature. The mini format keeps the plate light in hand and keeps the joint visible under your microscope.
Where It Fits in Your Rework Workflow
Reach for this plate when the repair involves parts that dislike direct hot air. You remove and install board-to-board connectors, repair Face ID flex cables and replace their connectors, and bottom-heat small flex cables and sub-boards before rework. It also warms flex-mounted ICs and small PCB sections, which cuts thermal shock before you start the main reflow. Technicians use it for IC reballing and FPC soldering, and the plate also suits small NAND and eMMC removal from the underside. On a dead phone with a lifted connector pad or a hardware fault in the Face ID flex, the plate gives you controlled bottom heat while flux, tweezers and your hot air station handle the main work. Keep a reballing kit and a PCB holder within reach, because this plate supports the job and does not hold the board for you.
Matching It to Your Iron and Knowing Its Limits
The plate fits T12 cartridge tips, JBC C210 and C245 tips, and 936 / 900M-T style tips. Confirm that your station runs one of those tip systems before you order. The package contains the heating plate only, so you buy the tip or handle and the station separately. This is a mini platform for small areas. It does not replace a full-size preheater, so step up to a larger preheating platform or a hot air station when you need to warm an entire motherboard. If you are building out your bench around it, browse our Soldering Stations, Hot Air Stations, Microscopes, PCB Holders and Reballing Kits categories for the tools that pair with this plate in daily repair work.
| Weight | 0.15 kg |
|---|
Key Features
- ✓99.99% pure copper plate for fast heat transfer
- ✓Hexagonal honeycomb heat-gathering surface for even heating
- ✓Fits T12, JBC C210/C245 and 936 / 900M-T style tips
- ✓Mini format for precise handling on small repairs
- ✓Simple to remove and install connectors and Face ID cables
- ✓Supports IC reballing and FPC soldering
- ✓Gives bottom heat that limits thermal shock on flex-mounted parts
- ✓Works with the soldering station you already own
Specifications
| Brand | Mechanic |
|---|---|
| Model | 900M-T-C6 |
| Category | Heating Platforms (Soldering Tool Accessory) |
| Compatibility | T12 cartridge tips, JBC C210 / C245 tips, 936 / 900M-T style tips |
| Technology | Honeycomb (hexagonal) heat-gathering structure |
| Material | 99.99% pure copper |
Common Repair Uses
- ✓Small-area bottom heating and rework for flex cables, connectors and sub-boards
- ✓Removing and installing board-to-board connectors
- ✓Face ID flex cable repair and connector replacement
- ✓Bottom-heating small flex cables before rework
- ✓Bottom-heating sub-boards before rework
- ✓Warming flex-mounted ICs and small PCB sections to reduce thermal shock
- ✓Micro soldering near heat-sensitive plastic where hot air is risky
- ✓IC reballing
- ✓FPC soldering
Compatible Devices
- ✓Universal accessory for iron tip systems, not specific to phone models
- ✓T12 cartridge tips
- ✓JBC C210 tips
- ✓JBC C245 tips
- ✓936-style tips
- ✓900M-T-style tips
- ✓T12-based soldering stations
- ✓JBC C210 / C245 tip-based soldering stations
- ✓Phone mainboards, flex cables and sub-boards as the work surface (universal, not model-specific)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which soldering iron tips does the 900M-T-C6 heating platform fit?
Can the 900M-T-C6 preheat a full phone motherboard?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



