Relife RL-093A 0.1mm Copper Heat Sink Sheet (50 Pcs)

₨ 999

Relife RL-093A Copper Heat Sink Sheet

The Relife RL-093A copper heat sink sheet gives your repair bench a 0.1mm copper shield for heat-sensitive chips. Each pack contains 50 sheets measuring approximately 12.45 × 14mm. You lay a sheet over a CPU, memory chip, or neighbouring IC before you start hot air work, and the copper draws heat away from the chip you want to protect. The ultra-thin profile sits flat on a crowded mainboard and leaves room for your nozzle, tweezers, and microscope view. Use it during reballing, IC change karna, and CPU rework on dead phones and hardware fault boards.

In stock

20 People watching this product now!
Description

Copper Heat Sink Sheet for Mobile Repair: Relife RL-093A 0.1mm

The Relife RL-093A is a copper heat sink sheet for mobile repair work that does one job well: it pulls heat away from chips you want to protect while you rework the chip next to them. Each pack holds 50 sheets at 0.1mm thickness, cut to approximately 12.45 × 14mm. You place a sheet on a CPU, memory IC, or power IC, fire up your hot air station, and the copper takes part of the thermal load instead of the silicon underneath.

Why 0.1mm Copper Suits a Crowded Mainboard

Modern phone boards pack ICs within millimetres of each other, so every fraction of height counts. At 0.1mm, the RL-093A adds almost nothing to the component stack. The sheet lies flat on the chip package, clears the nozzle path, and keeps your microscope view open. Copper conducts heat well, which makes it a logical material for drawing off hot air energy from the covered part. The series listing also describes the copper as corrosion resistant, so the sheets resist oxidation on a humid workshop bench. A footprint of approximately 12.45 × 14mm covers a compact IC package with a single sheet, so you skip trimming and stacking. A 50-piece pack suits shops that run several rework jobs per day, because you drop in a fresh sheet whenever the last one bends or discolours.

Where the RL-093A Fits in Your Rework Workflow

Heat control starts before you touch the board. Clamp the mainboard in a PCB holder, set your hot air station to the temperature the repair demands, and cover heat-sensitive neighbours such as the CPU, eMMC, or power ICs with copper sheets. Then start the reballing or IC change. The copper absorbs part of the heat from the covered chip, which lowers the risk of damage during long soldering and reflow cycles. When you pull an eMMC or UFS chip for work with eMMC programmers, UFS adapters, or ISP pinout tools, the sheets protect the chips that stay on the board. Pair them with your soldering station and reballing kit on dead phone boards, boot loop faults, and hang on logo cases that trace back to a hardware fault. After the job, run a multimeter check and a test box session to confirm the neighbouring chips survived the heat.

RL-093A vs RL-093B and RL-093C: Pick the Right Thickness

The Relife RL-093 series covers three copper thicknesses in 50-piece packs: RL-093A at 0.1mm, RL-093B at 0.3mm, and RL-093C at 0.5mm. Choose the 0.1mm RL-093A when you need the thinnest profile and minimal added height on a tight board. Step up to the thicker variants when the repair leaves more clearance and you want more copper mass between the heat source and the chip. Keeping all three on your bench lets you match the sheet to the board instead of forcing one thickness onto every job.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.1mm ultra-thin copper sheet that adds almost no height on a crowded board
  • 50 sheets per pack for high-volume repair shops
  • Approx. 12.45 × 14mm footprint that covers a compact IC package
  • Copper construction with high thermal conductivity for fast heat transfer
  • Corrosion-resistant copper that resists oxidation on the bench
  • Part of the Relife RL-093 series with 0.3mm (RL-093B) and 0.5mm (RL-093C) options
  • Fits reballing, CPU repair, and soldering workflows
  • Works alongside hot air stations, soldering stations, and reballing kits

Specifications

BrandRelife
ModelRL-093A (50 pcs per pack)
CategoryHeat Sink Sheets / Thermal Management Accessories
CompatibilityUniversal, not device-specific
MaterialCopper
DimensionsApprox. 12.45 × 14mm, 0.1mm thickness

Common Repair Uses

  • Heat control during hot air and soldering work on mainboards
  • BGA IC reballing
  • CPU repair and rework
  • IC change karna with hot air
  • Protecting neighbouring chips during soldering
  • Heat management on mainboards during refurbishment
  • Dead phone and hardware fault board repair

Compatible Devices

  • Universal copper heat sink sheet, not tied to any phone brand or chipset family
  • Mobile phone mainboard CPU chips
  • BGA ICs
  • IC chipsets on mainboards
  • Memory ICs near the rework area
  • Power ICs near the rework area
  • Compact chip packages near 12.45 × 14mm

FAQ

What is the product name?
The product name is Relife RL-093A 0.1mm Copper Heat Sink Sheet.
What is the brand of this product?
The brand of this product is Relife.
What is the model of this product?
The model of this product is RL-093A.
What is this product used for?
This product is used for managing heat on CPUs and ICs during reballing, rework, and soldering on mobile mainboards.
Which devices are compatible with this product?
This product is a universal copper heat sink sheet. It works on mainboard CPUs, BGA ICs, and IC chipsets and does not target any single phone brand.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the difference between Relife RL-093A, RL-093B, and RL-093C?
All three belong to the Relife RL-093 series and come in 50-piece packs. They differ in copper thickness: RL-093A is 0.1mm, RL-093B is 0.3mm, and RL-093C is 0.5mm.
What size are the RL-093A copper sheets and how many come in one pack?
Each RL-093A sheet measures approximately 12.45 × 14mm with a thickness of 0.1mm, and one pack contains 50 sheets.