Mechanic E8000 Acrylic Glue 50ml for Phone Repair
₨ 199
E8000 Acrylic Glue for Phone Repair at a Glance
The Mechanic E8000 is a transparent, one-component acrylic adhesive sold in a 50ml bottle with a steel nozzle. Its medium viscosity lets you place a controlled bead along a phone frame or glass edge without flooding the surrounding area. After curing, the bond stays flexible and waterproof rather than brittle. The adhesive sets at room temperature with no mixing, so the workflow stays simple at a standard repair bench. Surfaces dry to touch in roughly 3 to 6 minutes, while full cure takes 24 to 48 hours. Keep the cap tightly closed, because exposed glue thickens at the nozzle quickly.
Out of stock
E8000 Acrylic Glue for Phone Repair Benches
E8000 acrylic glue for phone repair work is a transparent, one-component adhesive for frame bonding, screen edge sealing, and small plastic or accessory repairs. You get a medium-viscosity bead that stays where you place it, so you can work on a tight frame without flooding the surrounding board or display edge. The bond cures at room temperature, which keeps the process simple on a standard bench. Once set, the joint remains flexible and waterproof instead of turning brittle. If you bond frames, back covers, and decorative parts every day, a 50ml bottle with a steel nozzle covers many jobs before you need to reorder.
Bonding Chemistry and Cure Behavior
This adhesive belongs to the acrylic family and works as a single component, so you never mix two parts before use. The glue sets on the surface within about three to six minutes, which gives you a short window to align parts before the bond locks in. Full cure takes roughly 24 to 48 hours, so leave the phone undisturbed during that period before you test it or apply stress. The final hardness sits in a soft range around 70 to 85A, which means the joint absorbs minor flex instead of cracking under light pressure. The cured film stays transparent, so the joint remains nearly invisible on clear or light-colored parts. Cure speed depends on room temperature, so keep your work area between 18 and 32 degrees for the most predictable result on every job.
Step-by-Step Bonding Workflow at Your Bench
Start by cleaning both surfaces with isopropyl alcohol and letting them dry completely, because dust and moisture weaken the bond. Next, apply a thin, even bead along one surface through the steel nozzle, and keep the layer light to avoid squeeze-out. Press the parts together within the first few minutes, then hold them firmly until the glue reaches a solid state. Clamps, a PCB holder, or light tape keep alignment steady during this phase. Before you run any test on a repaired phone, leave the device untouched for the full cure window. For larger surfaces, run a small trial on an offcut first so you can judge the spread and working time. Reseal the cap tightly after every session, since air contact thickens the glue at the nozzle and shortens the working life of the bottle.
Storage, Handling and Safety Notes
Store the bottle between 10 and 28 degrees Celsius and keep it away from heat sources. Glue left in an open or loosely capped bottle hardens quickly, so close the cap after every session without exception. The adhesive can irritate skin and eyes, so work in a well-ventilated area and wear gloves during longer sessions. If glue reaches your eyes, rinse them with plenty of water and seek medical advice if irritation continues. Keep the bottle out of reach of children at all times, and do not place it near flames during use. Before each new job, check the cap and nozzle, because a partly cured nozzle releases uneven beads and wastes part of the bottle.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Transparent acrylic formula for near-invisible bonds
- ✓Medium viscosity for controlled bead placement
- ✓One-component, room-temperature curing with no mixing
- ✓Surface dry in about 3 to 6 minutes
- ✓Flexible, waterproof cured joint
- ✓50ml bottle with steel nozzle
- ✓Low odor during application
- ✓Suitable for metal, glass, plastic, rubber, and fabric
Specifications
| Brand | Mechanic |
|---|---|
| Model | E8000 |
| Category | Adhesives and Glue |
| Compatibility | Universal, not device-specific |
| Supported Devices | Universal, not device-specific |
| Technology | Acrylic, one-component, room-temperature curing, 50ml with steel nozzle |
Common Repair Uses
- ✓Reattaching a loose phone frame during chassis rebuilds
- ✓Sealing the edge of a touch screen after glass replacement
- ✓Bonding a cracked plastic back cover
- ✓Securing loose plastic clips inside a housing
- ✓Repairing small rubber or silicone parts
- ✓Fixing rhinestone and decorative accessories on phone cases
- ✓Bonding decorative trim on phone cases
- ✓Gluing lightweight parts on a repair bench during reassembly
Compatible Devices
- ✓Universal, not device-specific. Scope covers general material bonding.
- ✓Smartphone frame and chassis bonding (general, not model-specific)
- ✓Touch screen and glass edge sealing
- ✓Plastic back covers and housings (ABS, PVC, PP, PE)
- ✓Nylon and rubber parts
- ✓Metal and ceramic surfaces
- ✓Glass and fiberglass components
- ✓Rhinestones and jewelry bead bonding
- ✓Fabric, leather, and paper materials



