2UUL SC06 Hand Actuated Glue Gun for 30ml Tubes
₨ 1,500
Precision 30ml Manual Dispensing Gun
The 2UUL SC06 is a hand actuated glue gun for mobile repair benches that need controlled dispensing from 30ml tubes. You squeeze the ergonomic handle and the gun pushes out solder paste, flux, UV solder mask oil, UV glue or structural adhesive with smooth, even force. Your grip sets the flow, so you place small beads exactly where the board needs them and cut overflow and wasted material. The body combines polymer engineering plastic with metal fittings for a light but rigid feel. Use it for reballing, IC rework prep, track protection and precision bonding.
In stock
Hand Actuated Glue Gun for Mobile Repair: 2UUL SC06 Overview
The 2UUL SC06 is a hand actuated glue gun for mobile repair work that dispenses paste and liquid materials from 30ml tubes. It does not heat anything. You squeeze the handle, the plunger drives the material through the needle, and your grip pressure decides how much comes out. If you work with solder paste, flux, UV solder mask oil or structural adhesive, this gun replaces raw thumb pressure on a bare syringe, which tires your hand and pushes out uneven amounts. 2UUL designed the SC06 for technicians who dispense small, repeatable quantities during board-level work.
Smooth, Even Force Through a Manual Mechanism
The SC06 uses a hand-actuated pressure mechanism. A squeeze on the handle moves the plunger forward, and material leaves the needle at a rate that matches your grip. That direct link gives you smooth, even force from the first press to the last. It matters when you lay solder paste on a BGA pad or flow UV solder mask oil over a repaired track, because a sudden surge ruins the placement and costs you material.
A thumb-driven syringe tends to overflow and waste paste. The SC06 handle spreads the load across your palm, so you control the bead more easily and waste less. The ergonomic grip keeps your hand relaxed through a long shift of repeated dispensing, which helps when you handle several boards in a row. Polymer engineering plastic and metal fittings form the body, so the mechanism stays rigid under repeated pressure while the gun stays light enough to position precisely under a microscope.
Where the Hand Actuated Glue Gun Fits in Mobile Repair
Many boards arrive as a dead phone, a charging issue or a hang on logo case, and most of them need rework before a software fix helps. When you do IC change karna on a board, you apply flux before the hot air station heats the chip, and you apply solder paste when you reball a BGA component. The SC06 holds the 30ml tube of flux or paste and delivers the material exactly where the work needs it.
After the soldering finishes, the same gun carries UV solder mask oil to protect repaired tracks, or structural adhesive to bond parts. Pair it with a PCB holder to fix the board, a microscope for placement and a reballing kit for BGA work, and your bench handles dispensing in one controlled step. You also cut cleanup time at your soldering station, because the material goes on the board and not around it.
What to Check Before You Buy
The SC06 takes 30ml tubes only, so confirm your syringe size before you order. It dispenses solder paste, flux, UV glue, UV solder mask oil and structural adhesive. It does not melt glue sticks, so it does not replace a hot melt glue gun, and you should not expect it to heat any material.
Press the handle gently and avoid excessive pressure, because steady force gives you cleaner beads than hard squeezes. Wipe the nozzle after every use so paste does not cure and block the tip, and store the gun in a dry place between jobs. For a repair shop owner, the SC06 gives every technician on the bench the same controlled dispensing at a low tool cost. Mechanicpk supplies the tool alongside multimeters, test boxes, eMMC programmers and the other bench equipment your workshop runs on.
| Weight | 0.3 kg |
|---|
Key Features
- ✓Hand-actuated pressure control for smooth, even dispensing
- ✓Takes 30ml tubes and syringes
- ✓Dispenses solder paste, flux, UV glue, UV solder mask oil and structural adhesive
- ✓Ergonomic handle that reduces hand fatigue
- ✓Light body of polymer engineering plastic with metal fittings
- ✓Controlled output that limits overflow and wasted material
- ✓Manual operation with no heating element, battery or cable
- ✓Suits technician benches and busy repair shops
Specifications
| Brand | 2UUL |
|---|---|
| Model | SC06 |
| Category | Hand Actuated Glue Gun / Manual Dispensing Tool |
| Compatibility | 30ml tubes and syringes |
| Technology | Manual hand-actuated pressure mechanism |
| Material | Polymer engineering plastic with metal fittings |
Common Repair Uses
- ✓Controlled dispensing of paste and liquid materials during mobile phone board repair and precision bonding.
- ✓Applying solder paste during BGA reballing
- ✓Dispensing flux before and during IC change
- ✓Coating repaired tracks with UV solder mask oil
- ✓Applying UV glue for precision bonding
- ✓Bonding parts with structural adhesive
- ✓Dispensing needle paste from 30ml tubes
- ✓Placing small, repeatable beads under a microscope
- ✓Reducing overflow and material waste at the repair bench
Compatible Devices
- ✓Universal dispensing tool for 30ml tubes and syringes. It does not target specific phone models or chipset families.
- ✓30ml solder paste tubes and syringes
- ✓30ml flux tubes and syringes
- ✓30ml UV solder mask oil syringes
- ✓30ml UV glue tubes
- ✓30ml structural adhesive tubes
- ✓30ml needle paste tubes
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the 2UUL SC06 use hot melt glue sticks?
Which materials can I dispense with the 2UUL SC06 for board repair?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



