Mechanic FS-51 Glue Removal Quick Spade Blade (Set) 5in1

₨ 999

Mechanic FS-51 Glue Removal Blade Set

The Mechanic FS-51 Glue Removal Quick Spade Blade (Set) 5in1 gives repair technicians thin 0.3 mm stainless-steel spade blades for clearing cured adhesive from CPU, IC and PCB pads. The anti-static designation suits board-level work, and the quick-change blade design keeps a sharp edge ready between jobs. This 5in1 set covers glue removal, scraping, cutting, chip prying and CPU layer disassembly during motherboard rework. Mechanicpk supplies it to Pakistani repair shops and service centers that clean pads before reballing or IC replacement. Order the set to keep spare edges on your bench.

In stock

19 People watching this product now!
Description

Mechanic FS-51 Glue Removal Blade Set for Mobile Repair Benches

The Mechanic FS-51 Glue Removal Quick Spade Blade (Set) 5in1 works as a glue removal blade set for mobile repair benches that deal with cured adhesive around CPUs, ICs and PCB pads every day. Each blade uses 0.3 mm stainless steel, so the edge slides under hardened glue and epoxy residue that a general-purpose cutter handles poorly. The 5in1 set puts several blades in one pack, which means you swap to a fresh edge the moment one dulls instead of stopping the job. Mechanicpk supplies the FS-51 to Pakistani repair shops, service centers and training institutes that run board-level rework daily, and the blade matches the sequence those benches follow: heat, lift, scrape, clean, reball.

Blade Material and Edge Design

Mechanic specifies the FS-51 as 0.3 mm imported steel with a sharp edge and wear resistance. That thickness gives you a useful balance on a board: the blade slips into the gap between a chip edge and the PCB, yet it stays stiff enough to push stubborn glue off the pad in one stroke. The product designation also lists the blades as anti-static, which suits work near exposed ICs and logic board pads. Mechanic does not publish a numeric ESD rating, so keep your normal bench grounding and wrist strap as your primary protection. The quick-change design lets you replace a worn blade without replacing the whole tool, which extends service life and keeps your consumable cost predictable across a busy week.

Where the FS-51 Fits in Your Repair Workflow

Glue removal sits between heating and reballing. After you lift a chip with your Hot Air Station, adhesive stays on the pads and around the chip edge. You scrape that residue with the FS-51, finish the pads with your Soldering Station and flux, and check the result under a Microscope. The same blade pries chips and separates CPU layers where glue seals stacked boards together. Boards that arrive as a dead phone, with a boot loop issue, hang on logo or dead after flash often need chip-level work, and chip-level work starts with clean pads. Clamp the board in a PCB Holder, confirm continuity with a Multimeter once the pads are clear, then move on to your Reballing Kits. For storage-chip jobs, pair the FS-51 with the ISP Pinout Tools, eMMC Programmers and UFS Adapters in our catalog, and keep a Test Box nearby for post-repair checks.

Using Glue Removal Blades Without Damaging the Board

Warm the board with your hot air station first so the adhesive softens, then work the blade at a shallow angle from the chip edge outward. Keep the edge flat against the pad and use short strokes. Deep digging lifts pads and turns a simple IC replacement into a track repair. Stop and inspect under the microscope after each pass, and clean the area with flux before you continue. When the blade edge rolls or chips, swap it immediately, because a dull edge forces extra pressure and extra pressure damages pads. A multi-blade set removes the temptation to push a worn edge through one more job. Treat the FS-51 as a sharp tool: store the blades in their pack and keep them away from the work area when you finish.

Additional information
Weight0.35 kg
Q & A
Please login to post questions

Key Features

  • 0.3 mm stainless-steel spade blades
  • Sharp, wear-resistant edge
  • Anti-static designation
  • Quick-change blades extend tool service life
  • Removes stubborn adhesive from CPU motherboard pads
  • Suitable for chip prying and CPU layer disassembly
  • Handles cutting and scraping of cured adhesive
  • 5in1 set keeps spare edges ready

Specifications

Brand EntityMechanic
Product EntityMechanic FS-51 Glue Removal Quick Spade Blade Set
Technology Entity0.3 mm stainless-steel anti-static spade blade
Compatible Device EntitiesSmartphone motherboards, CPU/SoC pads, IC chips, PCB boards
Repair Process EntityAdhesive removal, chip prying, CPU layer disassembly, pad cleaning before reballing
Industry EntityMobile phone repair, PCB repair, board-level rework

Common Repair Uses

  • Adhesive removal and chip-level preparation on mobile motherboards
  • Removing residual adhesive from CPU motherboard pads
  • Scraping glue and epoxy residue around ICs
  • Prying chips during removal
  • CPU layer disassembly
  • Cutting and scraping cured adhesive
  • Cleaning pads before reballing or IC replacement

Compatible Devices

  • Universal, not device-specific. Works on any board where cured adhesive needs removal.
  • Smartphone motherboards (all brands)
  • CPU and SoC pad areas
  • IC chip edges and surrounding adhesive
  • General PCB boards with cured glue residue
  • CPU layer joints on stacked boards

FAQ

What is the product name?
The product name is Mechanic FS-51 Glue Removal Quick Spade Blade (Set) 5in1.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is FS-51.
What is this product used for?
This product is used for removing cured adhesive from CPU, IC and PCB pads, scraping, cutting, chip prying and CPU layer disassembly.
Which devices are compatible with this product?
This product is universal and not device-specific. It works on any motherboard or PCB where cured adhesive needs removal.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How thick are the Mechanic FS-51 blades and what are they made of?
The blades are 0.3 mm thick and use stainless steel with a sharp, wear-resistant edge.
Can the FS-51 blades clear glue from CPU pads and pry chips on a motherboard?
Yes. Mechanic lists the FS-51 for removing residual adhesive from CPU motherboard pads, chip prying and CPU layer disassembly.