YCS Z04 Syringe Welding Oil Booster Rod (5cc)
₨ 600
Precise Flux Dosing for PCB Repair
The YCS Z04 Syringe Welding Oil Booster Rod (5cc) turns a standard 5ml syringe into a controlled dispenser. You push welding oil, green oil, rosin or tin paste onto the pad in measured amounts instead of squeezing the plunger with your thumb. The rod gives steady rebound feedback, so flux flows evenly during mobile phone PCB and BGA chip repair. The body measures 138 x 28 x 20 mm and the pack includes three needles. Mechanicpk supplies this booster to technicians and repair shops across Pakistan who want cleaner pads and less wasted flux.
In stock
Welding Oil Syringe Booster Built for Daily PCB Rework
A welding oil syringe booster gives you control over the one consumable that touches almost every board-level repair: flux. The YCS Z04 Syringe Welding Oil Booster Rod (5cc) fits a 5ml syringe of soldering oil, green oil, rosin or tin paste. It replaces thumb pressure with a rod that pushes the material out in a stable, even flow. On a dead phone or a stubborn hardware fault, a blob of flux in the wrong spot costs you cleaning time. This booster helps you place the amount you need exactly where the pad sits.
How the YCS Z04 Handles Flux, Green Oil and Tin Paste
The Z04 targets 5ml (5cc) syringes, the size most technicians load with welding oil and green oil. The oil slot holds the syringe firmly and resists loosening while you work. The rod delivers strong rebound feedback as you press, which keeps discharge balanced and smooth instead of surging out in bursts. That matters most with thick materials like tin paste and rosin, which fight a bare plunger. The body measures 138 x 28 x 20 mm, so it sits easily in one hand beside your hot air station or soldering station. The pack includes the booster and three needles, so you can keep flux and paste on separate tips. The booster is built for repeated use under normal conditions, so one unit covers heavy daily bench work.
Where It Fits in Your Repair Workflow
Flux enters almost every board-level job in your workshop. When you do an IC change, you clean the old solder off the pads and lay a thin, even layer of flux before the new chip goes down. When you reball a BGA, flux spreads across the pads before the stencil and solder balls go on. When you rebuild a damaged pad or run a jumper wire, tin paste goes exactly where the trace broke. The Z04 handles all of these with one hand while your other hand steadies the board in a PCB holder.
Under a microscope, controlled discharge lets you place a small, deliberate bead on the pad. That keeps residue away from neighbouring components and shortens the cleanup you do with brush and alcohol afterward. Charging issue, display problem, network issue or boot loop caused by a hardware fault: the flux step stays the same, and steady dosing helps in every one of them.
Choosing a Flux Booster for Your Bench
A hand-squeezed syringe drips, surges and wastes tin paste. A booster rod removes that variable, so you spend less time wiping excess and more time on the repair. Pair the Z04 with a reliable hot air station, a soldering station, a reballing kit and a multimeter for post-repair checks, and your flux, heat and test steps stay consistent from one job to the next. This listing covers the 5cc version for 5ml syringes. A separate 10cc version exists, so confirm your syringe size before you order. Mechanicpk lists the YCS Z04 for repair shops, service centers and independent technicians across Pakistan.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Pushes soldering oil, green oil, rosin and tin paste out of 5ml syringes
- ✓Oil slot holds the syringe firmly and resists loosening
- ✓Strong rebound feedback for balanced, controlled discharge
- ✓Stable, uniform oil discharge with smooth paste flow
- ✓Compact 138 x 28 x 20 mm body for one-hand use
- ✓Three needles included in the pack
- ✓Reusable under normal use
- ✓Works across different repair consumables, including flux oil and green oil
Specifications
| Brand | YCS |
|---|---|
| Model | YCS-Z04 |
| Category | Repair Tools > Hand Tools |
| Compatibility | 5ml (5cc) syringes of soldering oil, green oil, rosin and tin paste |
| Supported Devices | Universal for mobile phone and electronic PCB repair, not phone-model specific |
| Technology | Manual push-rod syringe booster with rebound feedback |
| Dimensions | 138 x 28 x 20 mm |
Common Repair Uses
- ✓Flux and paste dosing during board-level rework
- ✓Applying flux before BGA reballing
- ✓Laying flux on cleaned pads during an IC change
- ✓Placing tin paste on damaged pads or broken traces
- ✓Flux application before hot air reflow
- ✓Pad rebuilding and jumper wire work under a microscope
- ✓Dispensing green oil during PCB repair
- ✓Controlled flux placement on dead phone and hardware fault boards
- ✓Reducing flux waste and cleanup on busy repair benches
Compatible Devices
- ✓Universal — works with 5ml syringe consumables, not tied to specific phone models
- ✓5ml (5cc) soldering oil (flux) syringes
- ✓5ml green oil syringes
- ✓5ml rosin syringes
- ✓5ml tin paste syringes
- ✓Mobile phone PCBs (all brands, universal)
- ✓Electronic PCBs and BGA chip boards



