Relife H01 Nano Cleaning Sponge for Mobile Repair
₨ 400
Nano Cleaning Sponge for Mobile Repair
The Relife H01 Nano Cleaning Sponge gives your repair bench 500 pre-cut, lint-free pieces of high-density nano sponge for flux, dust and micro-particle cleanup on PCBs. Use it after IC removal, before reballing, and during pad inspection on dead phone, charging issue and display problem jobs. The material works with the cleaning agents and solvent workflows you already use, and each piece goes straight onto the board with no cutting. Mechanicpk supplies the Relife H01 to Pakistani technicians, repair shops and service centers that want a dependable consumable for professional board-level work.
In stock
Nano Cleaning Sponge for Mobile Repair: Relife H01 Technical Overview
The Relife H01 Nano Cleaning Sponge is a nano cleaning sponge for mobile repair that targets the residue every board-level job leaves behind. Flux, dust and micro-particles stay on pads and around IC footprints after rework, and loose fibers from cotton swabs make the mess worse. Each box holds 500 pre-cut pieces of high-density nano-structured sponge, so you grab a clean piece for every joint instead of reusing a dirty one. Mechanicpk stocks the Relife H01 for Pakistani repair shops, service centers and technicians who want a consistent consumable at the bench. The H01 belongs in the consumables tray next to your flux, solder wire and desoldering wick, where it handles the cleanup step that decides whether the next joint holds.
Lint-Free PCB Cleaning Sponge Pieces for Board-Level Work
Cotton swabs shed fibers, and tissue leaves lint across fine-pitch pads. The Relife H01 uses a high-density nano-structured material that pulls dust, flux residue and micro-particles off the surface and holds them inside the sponge. Supplier data lists the pieces as lint-free, which matters when you clean around BGA footprints, connector pads and shield frame edges before a reflow. Every piece comes pre-cut, so you skip the blade and the uneven offcuts, and you keep one clean piece per component instead of dragging old flux across a fresh pad. The material also works with a range of cleaning agents and solvent workflows, so you keep the board-safe cleaner your shop already trusts and add the sponge as the wiping layer. Wet a piece, wipe the pads, and check the result under your microscope before you place the IC. Because every piece has the same size, you wipe each board the same way and compare results between jobs without guessing. Fresh pieces also keep contaminants from one board off the next, which protects your reballed joints and your reputation with customers.
Where It Fits in Your Repair Workflow
A dead phone with a charging issue usually ends with a charging IC or PMIC change. After you lift the old chip with your hot air station and tin the pads with your soldering station, flux residue still sits on the board. Run the Relife H01 nano sponge over the footprint before you reball or place the new part. The same step helps after a display problem repair, when you remove a connector or touch IC and need clean pads for the replacement. On eMMC and UFS jobs, clean the pads after chip removal, then attach your ISP pinout tool or UFS adapter to a clear surface. Technicians who chase a hardware fault also wipe flux off suspect areas before they probe with a multimeter, since clean copper makes burned traces, lifted pads and corrosion easier to spot. When a dead after flash phone needs an eMMC reball, a clean footprint gives your stencil and solder balls a flat, residue-free surface. The sponge sits beside your reballing kit, PCB holder and microscope as a consumable you restock every week.
Buying Notes for Repair Shops and Service Centers
The box holds 500 pieces, weighs 30 g and measures 135 × 110 × 55 mm, so it fits in a bench drawer beside your flux bottles. Treat each piece as a consumable: use a fresh one when the surface loads with flux, then replace it. One box covers a large number of boards, which keeps your cost per job low for shops that run several IC changes and pad cleanups a day. Service centers and training institutes can keep one box at each station and track the stock the same way they track flux and solder wire. Pair the Relife H01 with ISP pinout tools, eMMC programmers, hot air stations, soldering stations and reballing kits from Mechanicpk to build a complete cleaning-to-reflow workflow. Store the box closed and dry so the pieces stay clean until you use them.
| Weight | 0.30 kg |
|---|
Key Features
- ✓500 pre-cut pieces per box
- ✓High-density nano-structured sponge material
- ✓Lint-free pieces for precision electronics cleaning
- ✓Strong adsorption of dust, flux residue and micro-particles
- ✓Works with a range of cleaning agents and solvent workflows
- ✓Fresh piece for every joint, no cutting required
- ✓Compact box, 135 × 110 × 55 mm and 30 g
- ✓Suits workshop, service center and training lab use
Specifications
| Brand | Relife |
|---|---|
| Model | H01 |
| Category | Repair Accessories / Cleaning Consumables |
| Compatibility | Universal — not device-specific |
| Technology | High-density nano-structured sponge |
| Material | Nano cleaning sponge, high-density foam-like structure |
| Quantity per Box | 500 pieces |
| Dimensions | 135 × 110 × 55 mm |
| Weight | 30 g |
Common Repair Uses
- ✓Flux, dust and micro-particle cleanup at board level.
- ✓Cleaning flux residue after IC removal
- ✓Preparing pads before reballing
- ✓Wiping footprints before placing a new IC
- ✓Cleaning eMMC and UFS pads before ISP or adapter work
- ✓Dust removal on charging issue boards
- ✓Pad cleanup after display connector replacement
- ✓Clearing flux before multimeter probing on hardware fault jobs
- ✓Final wipe before microscope inspection
Compatible Devices
- ✓Universal — not device-specific. The sponge cleans board and component surfaces on any phone brand.
- ✓Smartphone logic boards (all brands)
- ✓IC footprints and BGA pads
- ✓Charging IC and PMIC pad areas
- ✓eMMC and UFS chip pad areas
- ✓Display and touch connector pads
- ✓Shield frame edges and solder points
- ✓Flux-contaminated PCB areas
- ✓Boards on a PCB holder or fixture



